=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2022.02.09 09:52:55 =~=~=~=~=~=~=~=~=~=~=~= [0000.250] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de) [0000.256] Processing in cold boot mode Bootloader 2 [0000.260] A02 Bootrom Patch rev = 1023 [0000.264] Power-up reason: pmc por [0000.267] No Battery Present [0000.270] pmic max77620 reset reason [0000.273] pmic max77620 NVERC : 0x50 [0000.277] RamCode = 0 [0000.279] Platform has DDR4 type RAM [0000.282] max77620 disabling SD1 Remote Sense [0000.286] Setting DDR voltage to 1125mv [0000.290] Serial Number of Pmic Max77663: 0xc16a4 [0000.298] Entering ramdump check [0000.301] Get RamDumpCarveOut = 0x0 [0000.304] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.309] Last reboot was clean, booting normally! [0000.314] Sdram initialization is successful [0000.318] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.324] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.330] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.336] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.342] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.348] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.353] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.359] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.375] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.381] Platform-DebugCarveout: 0 [0000.385] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.390] Non secure mode, and RB not enabled. [0000.407] Csd NumOfBlocks=0 [0000.603] *** Booting BFS0. [0000.605] Read PT from (0:3) [0000.611] Using BFS PT to query partitions [0000.615] PT: Partition LNX NOT found ! [0001.218] *** Booting KFS0. [0001.221] BoardID = 3448, SKU = 0x2 [0001.224] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.230] Read GPT from (0:3) [0001.237] Using GPT Primary to query partitions [0001.242] Loading Tboot-CPU binary [0001.249] Verifying TBC in OdmNonSecureSBK mode [0001.259] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0001.266] Bootloader downloaded successfully. [0001.270] Downloaded Tboot-CPU binary to 0xa0000258 [0001.275] MAX77620_GPIO5 configured [0001.278] CPU power rail is up [0001.281] CPU clock enabled [0001.285] Performing RAM repair [0001.288] Updating A64 Warmreset Address to 0xa00002e9 [0001.293] BoardID = 3448, SKU = 0x2 [0001.296] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.303] Loading NvTbootBootloaderDTB [0001.320] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0001.382] Bootloader DTB Load Address: 0x83000000 [0001.387] BoardID = 3448, SKU = 0x2 [0001.390] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.396] Loading NvTbootKernelDTB [0001.413] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0001.475] Kernel DTB Load Address: 0x83100000 [0001.479] BoardID = 3448, SKU = 0x2 [0001.483] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.490] Loading cboot binary [0001.501] Verifying EBT in OdmNonSecureSBK mode [0001.543] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0001.550] Bootloader downloaded successfully. [0001.554] BoardID = 3448, SKU = 0x2 [0001.557] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.563] PT: Partition NCT NOT found ! [0001.567] Warning: Find Partition via PT Failed [0001.571] Next binary entry address: 0x92c00258 [0001.576] BoardId: 3448 [0001.580] Overriding pmu board id with proc board id [0001.585] Display board id is not available [0001.589] BoardID = 3448, SKU = 0x2 [0001.593] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.606] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.659] /bpmp deleted [0001.661] SC7EntryFw header found loaded at 0xff700000 [0001.836] OVR2 PMIC [0001.837] Bpmp FW successfully loaded [0001.841] BoardID = 3448, SKU = 0x2 [0001.844] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.851] WB0 init successfully at 0xff780000 [0001.856] Set NvDecSticky Bits [0001.859] GSC2 address ff53fffc value c0edbbcc [0001.866] GSC MC Settings done [0001.868] BoardID = 3448, SKU = 0x2 [0001.872] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.878] TOS Image length 53680 [0001.881] Monitor size 53680 [0001.884] OS size 0 [0001.890] Secure Os AES-CMAC Verification Success! [0001.894] TOS image cipher info: plaintext [0001.898] Loading and Validation of Secure OS Successful [0001.914] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.919] NvTbootPackSdramParams: start. [0001.924] NvTbootPackSdramParams: done. [0001.927] Tegraboot started after 180550 us [0001.931] Basic modules init took 1457244 us [0001.936] Sec Bootdevice Read Time = 562 ms, Read Size = 14649 KB [0001.941] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.947] Next stage binary read took 7388 us [0001.951] Carveout took -28695 us [0001.954] CPU initialization took 357585 us [0001.958] Total time taken by TegraBoot 1793522 us [0001.963] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):5b49e7f80 NOTICE: BL31: Built : 08:37:40, Feb 19 2021 ERROR: Error initializing runtime service trusty_fast [0002.085] RamCode = 0 [0002.090] LPDDR4 Training: Read DT: Number of tables = 2 [0002.095] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0002.107] EMC Training Successful [0002.110] 408000 not found in DVFS table [0002.117] RamCode = 0 [0002.120] DT Write: emc-table@204000 succeeded [0002.125] DT Write: emc-table@1600000 succeeded [0002.130] LPDDR4 Training: Write DT: Number of tables = 2 [0002.190] [0002.191] Debug Init done [0002.193] Marked DTB cacheable [0002.196] Bootloader DTB loaded at 0x83000000 [0002.201] Marked DTB cacheable [0002.204] Kernel DTB loaded at 0x83100000 [0002.208] DeviceTree Init done [0002.221] Pinmux applied successfully [0002.225] gicd_base: 0x50041000 [0002.229] gicc_base: 0x50042000 [0002.232] Interrupts Init done [0002.236] Using base:0x60005090 & irq:208 for tick-timer [0002.241] Using base:0x60005098 for delay-timer [0002.245] platform_init_timer: DONE [0002.249] Timer(tick) Init done [0002.253] osc freq = 38400 khz [0002.256] [0002.257] Welcome to L4T Cboot [0002.260] [0002.261] Cboot Version: 00.00.2018.01-t210-39562017 [0002.266] calling constructors [0002.269] initializing heap [0002.272] initializing threads [0002.275] initializing timers [0002.278] creating bootstrap completion thread [0002.282] top of bootstrap2() [0002.285] CPU: ARM Cortex A57 [0002.288] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0002.293] initializing platform [0002.346] Config for emmc ddr50 mode completed [0002.350] sdmmc bdev is already initialized [0002.354] Enable APE clock [0002.357] Un-powergate APE partition [0002.361] of_register: registering tegra_udc to of_hal [0002.366] of_register: registering inv20628-driver to of_hal [0002.371] of_register: registering ads1015-driver to of_hal [0002.377] of_register: registering lp8557-bl-driver to of_hal [0002.383] of_register: registering bq2419x_charger to of_hal [0002.388] of_register: registering bq27441_fuel_gauge to of_hal [0002.399] gpio framework initialized [0002.403] of_register: registering tca9539_gpio to of_hal [0002.408] of_register: registering tca9539_gpio to of_hal [0002.413] of_register: registering i2c_bus_driver to of_hal [0002.419] of_register: registering i2c_bus_driver to of_hal [0002.424] of_register: registering i2c_bus_driver to of_hal [0002.430] pmic framework initialized [0002.434] of_register: registering max77620_pmic to of_hal [0002.439] regulator framework initialized [0002.443] of_register: registering tps65132_bl_driver to of_hal [0002.449] initializing target [0002.455] gpio_driver_register: register 'tegra_gpio_driver' driver [0002.465] fixed regulator driver initialized [0002.482] initializing OF layer [0002.485] NCK carveout not present [0002.488] Skipping dts_overrides [0002.492] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.507] I2C Bus Init done [0002.509] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.519] I2C Bus Init done [0002.522] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.532] I2C Bus Init done [0002.535] of_children_init: Ops found for compatible string ti,tca9539 [0002.544] tca9539_init: i2c bus: 3, slave addr: 0xe8 [0002.551] gpio_driver_register: register 'tca9539_gpio_driver' driver [0002.558] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.568] I2C Bus Init done [0002.570] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.580] I2C Bus Init done [0002.583] of_children_init: Ops found for compatible string maxim,max77620 [0002.593] max77620_init using irq 118 [0002.598] register 'maxim,max77620' pmic [0002.602] gpio_driver_register: register 'max77620-gpio' driver [0002.608] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.618] I2C Bus Init done [0002.622] NCK carveout not present [0002.627] Cannot find the PM_EEPR_MNG [0002.630] no eeprom position or read error [0002.660] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.666] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.674] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.680] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.688] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3e:36:09 [0002.694] Plugin Manager: Parse ODM data 0x000a4000 [0002.705] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.715] Cannot find the PM_EEPR_MNG [0002.719] no eeprom position or read error [0002.749] Add serial number:1421621004284 as DT property [0002.756] Applying platform configs [0002.762] platform-init is not present. Skipping [0002.766] calling apps_init() [0002.787] Found 17 GPT partitions in "sdmmc3_user" [0002.792] Proceeding to Cold Boot [0002.795] starting app android_boot_app [0002.799] Device state: unlocked [0002.802] display console init [0002.810] could not find regulator [0002.833] hdmi cable not connected [0002.837] is_hdmi_needed: HDMI not connected, returning false [0002.842] hdmi is not connected [0002.846] sor0 is not supDT entry for leds-pwm not found p[0002.853] orted [0002.855] display_console_init: no valid display out_type [0002.863] subnode volume_up is not found ! [0002.866] subnode back is not found ! [0002.870] subnode volume_down is not found ! [0002.874] subnode menu is not found ! [0002.878] Gpio keyboard init success [0002.925] found decompressor handler: lz4-legacy [0002.940] decompressing blob (type 1)... [0003.006] display_resolution: No display init [0003.010] Failed to retrieve display resolution [0003.014] Could not load/initialize BMP blob...ignoring [0003.064] decompressor handler not found [0003.068] load_firmware_blob: Firmware blob loaded, entries=2 [0003.074] XUSB blob version 0 size 124416 @ 0x92cb328c [0003.080] -------> se_aes_verify_sbk_clear: 747 [0003.084] se_aes_verify_sbk_clear: Error [0003.088] SE operation failed [0003.091] bl_battery_charging: connected to external power supply [0003.100] display_console_ioctl: No display init [0003.104] switch_backlight failed [0003.114] device_query_partition_size: failed to open partition sdmmc3_user:MSC ! [0003.121] MSC Partition not found [0003.131] device_query_partition_size: failed to open partition sdmmc3_user:USP ! [0003.138] USP partition read failed! [0003.142] blob_init: blob-partition USP header read failed [0003.147] android_boot Unable to update recovery partition [0003.152] kfs_getpartname: name = LNX [0003.156] Loading kernel from LNX [0003.250] load kernel from storage [0003.260] decompressor handler not found [0003.294] Successfully loaded kernel and ramdisk images [0003.299] board ID = D78, board SKU = 2 [0003.304] display_resolution: No display init [0003.308] Failed to retrieve display resolution [0003.312] bmp blob is not loaded and initialized [0003.317] Failed to display boot-logo [0003.321] NCK carveout not present [0003.324] Skipping dts_overrides [0003.327] NCK carveout not present [0003.332] Cannot find the PM_EEPR_MNG [0003.336] no eeprom position or read error [0003.366] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.371] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0003.379] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.385] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0003.393] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3e:36:09 [0003.400] Plugin Manager: Parse ODM data 0x000a4000 [0003.411] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0003.419] Add serial number:1421621004284 as DT property [0003.427] "bpmp" doesn't exist, creating [0003.432] Updated bpmp info to DTB [0003.437] Updated initrd info to DTB [0003.440] "proc-board" doesn't exist, creating [0003.446] Updated board info to DTB [0003.450] "pmu-board" doesn't exist, creating [0003.455] Updated board info to DTB [0003.459] "display-board" doesn't exist, creating [0003.464] Updated board info to DTB [0003.468] "reset" doesn't exist, creating [0003.472] Updated reset info to DTB [0003.476] display_console_ioctl: No display init [0003.480] display_console_ioctl: No display init [0003.485] display_console_ioctl: No display init [0003.489] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt [0003.524] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0003.529] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [0003.546] Updated bootarg info to DTB [0003.549] Adding uuid 00000001643146c10800000007010240 to DT [0003.555] Adding eks info 0 to DT [0003.560] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0003.566] Updated memory info to DTB [0003.571] add_lp0_disable: Unable to find plugin-manager ids under chosen node! (FDT_ERR_NOTFOUND) [0003.583] set vdd_core voltage to 1075 mv [0003.587] setting 'vdd-core' regulator to 1075000 micro volts [0003.592] Found secure-pmc; disable BPMP U-Boot 2020.04-g6b630d64fd (Feb 19 2021 - 08:37:46 -0800) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... *** Warning - spi_flash_probe_bus_cs() failed, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 Card did not respond to voltage select! switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 879 bytes read in 20 ms (42 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7159841 bytes read in 176 ms (38.8 MiB/s) Retrieving file: /boot/Image 34338824 bytes read in 777 ms (42.1 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 00000000831752f5 copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (buildbrain@mobile-u64-5294-d8000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Feb 19 08:40:32 PST 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.528206] genirq: Setting trigger mode 8 for irq 57 failed (irq_chip_set_type_parent+0x0/0x48) [ 1.057263] tegradc tegradc.1: tegra_dc_parse_panel_ops: could not find panel for /host1x/sor [ 1.057304] tegradc tegradc.1: err:-19 parsing panel_ops [ 1.109250] nct1008_nct72 0-004c: write reg err -121 [ 1.114256] nct1008_nct72 0-004c: sensor init failed 0xffffff87 [ 1.120210] nct1008_nct72 0-004c: [ 1.120210] exit nct1008_probe, err=-121 [ 1.698705] cgroup: cgroup2: unknown option "nsdelegate" [ 3.108090] random: crng init done [ 3.111494] random: 7 urandom warning(s) missed due to ratelimiting [ 5.167365] encx24j600: no symbol version for module_layout [ 5.696289] [dhd] dhd_conf_set_chiprev : chip=0x4345, chiprev=9 [ 5.911230] [dhd-wlan0] wl_android_wifi_on : in g_wifi_on=0 [ 6.408021] [dhd] dhd_conf_read_config : Ignore config file /home/fd/modlues//config.txt [ 6.416221] [dhd] dhd_conf_set_path_params : Final fw_path=/home/fd/modlues/fw_bcm43456c5_ag.bin [ 6.425360] [dhd] dhd_conf_set_path_params : Final nv_path=/home/fd/modlues//nvram.txt [ 6.433489] [dhd] dhd_conf_set_path_params : Final clm_path=/home/fd/modlues/clm_bcm43456c5_ag.blob [ 6.442603] [dhd] dhd_conf_set_path_params : Final conf_path=/home/fd/modlues//config.txt [ 6.688945] [dhd] dhd_conf_set_txglom_params : txglom_mode=multi-desc [ 6.695986] [dhd] dhd_conf_set_txglom_params : txglomsize=36, deferred_tx_len=0 [ 6.703813] [dhd] dhd_conf_set_txglom_params : txinrx_thres=128, dhd_txminmax=-1 [ 6.711682] [dhd] dhd_conf_set_txglom_params : tx_max_offset=0, txctl_tmo_fix=300 [ 6.719370] [dhd] dhd_conf_get_disable_proptx : fw_proptx=1, disable_proptx=-1 [ 6.786525] [dhd] dhd_conf_map_country_list : CN/38 [ 6.791706] [dhd] dhd_conf_set_country : set country CN, revision 38 [ 6.802637] [dhd] dhd_conf_set_country : Country code: CN (CN/38) [ 6.817366] [dhd-wlan0] wl_android_wifi_on : Success [ 7.012732] [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 0, bssidx: 0 [ 10.166725] [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 1, bssidx: 0 Ubuntu 18.04.5 LTS fd-desktop ttyS0 fd-desktop login: