[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x50 [0000.151] RamCode = 0 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x13b68 [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.178] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.198] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.233] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] BoardID = 3448, SKU = 0x0 [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.276] Nano-SD: checking PT table on QSPI ... [0000.280] Read PT from (2:0) [0000.296] Using BFS PT to query partitions [0000.301] Loading Tboot-CPU binary [0000.330] Verifying TBC in OdmNonSecureSBK mode [0000.340] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.347] Bootloader downloaded successfully. [0000.351] Downloaded Tboot-CPU binary to 0xa0000258 [0000.356] MAX77620_GPIO5 configured [0000.359] CPU power rail is up [0000.362] CPU clock enabled [0000.366] Performing RAM repair [0000.369] Updating A64 Warmreset Address to 0xa00002e9 [0000.374] BoardID = 3448, SKU = 0x0 [0000.377] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.381] Nano-SD: checking PT table on QSPI ... [0000.385] Loading NvTbootBootloaderDTB [0000.452] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.525] Bootloader DTB Load Address: 0x83000000 [0000.530] BoardID = 3448, SKU = 0x0 [0000.533] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.537] Nano-SD: checking PT table on QSPI ... [0000.541] Loading NvTbootKernelDTB [0000.607] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.680] Kernel DTB Load Address: 0x83100000 [0000.684] BoardID = 3448, SKU = 0x0 [0000.688] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.691] Nano-SD: checking PT table on QSPI ... [0000.698] Loading cboot binary [0000.813] Verifying EBT in OdmNonSecureSBK mode [0000.855] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.862] Bootloader downloaded successfully. [0000.866] BoardID = 3448, SKU = 0x0 [0000.870] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.873] Nano-SD: checking PT table on QSPI ... [0000.878] PT: Partition NCT NOT found ! [0000.882] Warning: Find Partition via PT Failed [0000.886] Next binary entry address: 0x92c00258 [0000.891] BoardId: 3448 [0000.895] Overriding pmu board id with proc board id [0000.900] Display board id is not available [0000.904] BoardID = 3448, SKU = 0x0 [0000.907] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.911] Nano-SD: checking PT table on QSPI ... [0001.016] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.073] /bpmp deleted [0001.075] SC7EntryFw header found loaded at 0xff700000 [0001.270] OVR2 PMIC [0001.272] Bpmp FW successfully loaded [0001.276] BoardID = 3448, SKU = 0x0 [0001.279] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.283] Nano-SD: checking PT table on QSPI ... [0001.288] WB0 init successfully at 0xff780000 [0001.293] Set NvDecSticky Bits [0001.296] GSC2 address ff53fffc value c0edbbcc [0001.302] GSC MC Settings done [0001.305] BoardID = 3448, SKU = 0x0 [0001.309] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.312] Nano-SD: checking PT table on QSPI ... [0001.318] TOS Image length 53680 [0001.321] Monitor size 53680 [0001.324] OS size 0 [0001.339] Secure Os AES-CMAC Verification Success! [0001.343] TOS image cipher info: plaintext [0001.347] Loading and Validation of Secure OS Successful [0001.363] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.368] NvTbootPackSdramParams: start. [0001.373] NvTbootPackSdramParams: done. [0001.377] Tegraboot started after 51830 us [0001.381] Basic modules init took 886375 us [0001.385] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.390] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.396] Next stage binary read took 102859 us [0001.400] Carveout took -126356 us [0001.403] CPU initialization took 495394 us [0001.407] Total time taken by TegraBoot 1358272 us [0001.412] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):5b49e7f80 NOTICE: BL31: Built : 08:37:40, Feb 19 2021 ERROR: Error initializing runtime service trusty_fast [0001.534] RamCode = 0 [0001.539] LPDDR4 Training: Read DT: Number of tables = 2 [0001.544] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.557] EMC Training Successful [0001.560] 408000 not found in DVFS table [0001.566] RamCode = 0 [0001.570] DT Write: emc-table@204000 succeeded [0001.575] DT Write: emc-table@1600000 succeeded [0001.579] LPDDR4 Training: Write DT: Number of tables = 2 [0001.626] [0001.627] Debug Init done [0001.630] Marked DTB cacheable [0001.633] Bootloader DTB loaded at 0x83000000 [0001.637] Marked DTB cacheable [0001.640] Kernel DTB loaded at 0x83100000 [0001.644] DeviceTree Init done [0001.657] Pinmux applied successfully [0001.662] gicd_base: 0x50041000 [0001.665] gicc_base: 0x50042000 [0001.668] Interrupts Init done [0001.672] Using base:0x60005090 & irq:208 for tick-timer [0001.677] Using base:0x60005098 for delay-timer [0001.682] platform_init_timer: DONE [0001.685] Timer(tick) Init done [0001.689] osc freq = 38400 khz [0001.693] [0001.694] Welcome to L4T Cboot [0001.697] [0001.698] Cboot Version: 00.00.2018.01-t210-39562017 [0001.703] calling constructors [0001.706] initializing heap [0001.709] initializing threads [0001.712] initializing timers [0001.715] creating bootstrap completion thread [0001.719] top of bootstrap2() [0001.722] CPU: ARM Cortex A57 [0001.725] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.729] initializing platform [0001.737] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.742] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.746] Macronix QSPI chip present [0001.749] SPI device register [0001.752] init boot device [0001.755] allocating memory for boot device(SPI) [0001.760] registering boot device [0001.778] QSPI bdev is already initialized [0001.782] Enable APE clock [0001.784] Un-powergate APE partition [0001.788] of_register: registering tegra_udc to of_hal [0001.793] of_register: registering inv20628-driver to of_hal [0001.799] of_register: registering ads1015-driver to of_hal [0001.804] of_register: registering lp8557-bl-driver to of_hal [0001.810] of_register: registering bq2419x_charger to of_hal [0001.816] of_register: registering bq27441_fuel_gauge to of_hal [0001.827] gpio framework initialized [0001.831] of_register: registering tca9539_gpio to of_hal [0001.836] of_register: registering tca9539_gpio to of_hal [0001.841] of_register: registering i2c_bus_driver to of_hal [0001.847] of_register: registering i2c_bus_driver to of_hal [0001.853] of_register: registering i2c_bus_driver to of_hal [0001.858] pmic framework initialized [0001.862] of_register: registering max77620_pmic to of_hal [0001.867] regulator framework initialized [0001.871] of_register: registering tps65132_bl_driver to of_hal [0001.877] initializing target [0001.883] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.891] board ID = D78, board SKU = 0 [0001.895] Skipping Z3! [0001.899] fixed regulator driver initialized [0001.917] initializing OF layer [0001.920] NCK carveout not present [0001.923] Skipping dts_overrides [0001.928] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.945] I2C Bus Init done [0001.947] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.958] I2C Bus Init done [0001.960] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.971] I2C Bus Init done [0001.973] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.984] I2C Bus Init done [0001.986] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.997] I2C Bus Init done [0001.999] of_children_init: Ops found for compatible string maxim,max77620 [0002.010] max77620_init using irq 118 [0002.015] register 'maxim,max77620' pmic [0002.019] gpio_driver_register: register 'max77620-gpio' driver [0002.025] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.036] I2C Bus Init done [0002.039] NCK carveout not present [0002.049] Find /i2c@7000c000's alias i2c0 [0002.053] get eeprom at 1-a0, size 256, type 0 [0002.062] Find /i2c@7000c500's alias i2c2 [0002.066] get eeprom at 3-a0, size 256, type 0 [0002.070] get eeprom at 3-ae, size 256, type 0 [0002.075] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.080] I2C slave not started [0002.083] I2C write failed [0002.086] Writing offset failed [0002.089] eeprom_init: EEPROM read failed [0002.092] pm_ids_update: eeprom init failed [0002.097] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.127] pm_ids_update: The pm board id is 3448-0000-401 [0002.134] Adding plugin-manager/ids/3448-0000-401=/i2c@7000c500:module@0x50 [0002.142] pm_ids_update: pm id update successful [0002.146] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.177] pm_ids_update: The pm board id is 3449-0000-400 [0002.183] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.191] pm_ids_update: pm id update successful [0002.221] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.227] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.235] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.241] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.249] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:5b:a9:c2 [0002.255] Plugin Manager: Parse ODM data 0x000a4000 [0002.268] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70 006000 [0002.283] Find /i2c@7000c000's alias i2c0 [0002.286] get eeprom at 1-a0, size 256, type 0 [0002.295] Find /i2c@7000c500's alias i2c2 [0002.299] get eeprom at 3-a0, size 256, type 0 [0002.304] get eeprom at 3-ae, size 256, type 0 [0002.308] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.313] I2C slave not started [0002.316] I2C write failed [0002.319] Writing offset failed [0002.322] eeprom_init: EEPROM read failed [0002.326] pm_ids_update: eeprom init failed [0002.330] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.360] pm_ids_update: The pm board id is 3448-0000-401 [0002.366] Adding plugin-manager/ids/3448-0000-401=/i2c@7000c500:module@0x50 [0002.373] pm_ids_update: pm id update successful [0002.378] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.408] pm_ids_update: The pm board id is 3449-0000-400 [0002.414] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.421] pm_ids_update: pm id update successful [0002.452] Add serial number:1424121072650 as DT property [0002.459] Applying platform configs [0002.466] platform-init is not present. Skipping [0002.470] calling apps_init() [0002.476] Couldn't find GPT header [0002.481] Proceeding to Cold Boot [0002.484] starting app android_boot_app [0002.488] Device state: unlocked [0002.491] display console init [0002.499] could not find regulator [0002.503] hdmi cable connected [0002.518] edid read success [0002.533] edid DT entry for leds-pwm not found r[0002.541] ead success [0002.543] width = 640, height = 480, frequency = 25174825 [0002.548] width = 640, height = 480, frequency = 25174825 [0002.554] width = 1920, height = 1080, frequency = 174500000 [0002.560] width = 1920, height = 1080, frequency = 148500000 [0002.565] width = 1920, height = 1080, frequency = 148500000 [0002.571] width = 1920, height = 1080, frequency = 148351648 [0002.576] width = 1280, height = 720, frequency = 74175824 [0002.582] width = 720, height = 480, frequency = 26973026 [0002.587] width = 640, height = 480, frequency = 25174825 [0002.593] width = 1920, height = 1080, frequency = 148351648 [0002.598] width = 720, height = 576, frequency = 26973026 [0002.604] width = 1280, height = 720, frequency = 74175824 [0002.609] width = 1920, height = 1080, frequency = 148351648 [0002.615] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.623] tmds-config node not found [0002.627] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepr opsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.641] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.649] could not find regulator [0002.652] could not find regulator [0002.656] could not find regulator [0002.684] using default cmu settings [0002.687] dc_hdmi_enable, starting HDMI initialisation [0002.694] dc_hdmi_enable, HDMI initialisation complete [0002.699] list and configure display window [0002.707] display console init completed [0002.719] subnode volume_up is not found ! [0002.723] subnode back is not found ! [0002.726] subnode volume_down is not found ! [0002.730] subnode menu is not found ! [0002.734] Gpio keyboard init success [0002.815] found decompressor handler: lz4-legacy [0002.829] decompressing blob (type 1)... [0002.899] load_bmp_blob: panelresolution=1080 type=3 [0002.974] decompressor handler not found [0002.977] load_firmware_blob: Firmware blob loaded, entries=2 [0002.983] XUSB blob version 0 size 124416 @ 0x934ae28c [0002.989] -------> se_aes_verify_sbk_clear: 747 [0002.993] se_aes_verify_sbk_clear: Error [0002.997] SE operation failed [0003.000] bl_battery_charging: connected to external power supply [0003.012] device_query_partition_size: failed to open partition spiflash0:MSC ! [0003.020] MSC Partition not found [0003.026] device_query_partition_size: failed to open partition spiflash0:USP ! [0003.033] USP partition read failed! [0003.037] blob_init: blob-partition USP header read failed [0003.042] android_boot Unable to update recovery partition [0003.048] kfs_getpartname: name = LNX [0003.051] Loading kernel from LNX [0003.061] Found 19 BFS partitions in "spiflash0" [0003.380] load kernel from storage [0003.385] decompressor handler not found [0003.650] Successfully loaded kernel and ramdisk images [0003.655] board ID = D78, board SKU = 0 [0003.660] sdmmc node status = okay [0003.663] sdcard instance = 0 [0003.666] sdcard gpio handle 0x5b [0003.669] sdcard gpio pin 0xc9 [0003.672] sdcard gpio flags 0x0 [0003.675] vmmc-supply 0x9e [0003.677] cd_gpio_pin = 201 [0003.680] pin_state = 0 [0003.682] Found sdcard [0003.685] SD-card IS present ... [0003.688] load_and_boot_kernel: SD card detected OK [0003.694] load_bmp_blob: panelresolution=1080 type=3 [0004.188] display bmp image done [0004.191] NCK carveout not present [0004.194] Skipping dts_overrides [0004.197] NCK carveout not present [0004.207] Find /i2c@7000c000's alias i2c0 [0004.211] get eeprom at 1-a0, size 256, type 0 [0004.220] Find /i2c@7000c500's alias i2c2 [0004.224] get eeprom at 3-a0, size 256, type 0 [0004.228] get eeprom at 3-ae, size 256, type 0 [0004.233] pm_ids_update: Updating 1,a0, size 256, type 0 [0004.238] I2C slave not started [0004.241] I2C write failed [0004.244] Writing offset failed [0004.247] eeprom_init: EEPROM read failed [0004.251] pm_ids_update: eeprom init failed [0004.255] pm_ids_update: Updating 3,a0, size 256, type 0 [0004.285] pm_ids_update: The pm board id is 3448-0000-401 [0004.292] Adding plugin-manager/ids/3448-0000-401=/i2c@7000c500:module@0x50 [0004.300] pm_ids_update: pm id update successful [0004.305] pm_ids_update: Updating 3,ae, size 256, type 0 [0004.335] pm_ids_update: The pm board id is 3449-0000-400 [0004.341] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0004.349] pm_ids_update: pm id update successful [0004.379] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.385] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0004.393] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.399] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0004.407] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:5b:a9:c2 [0004.413] Plugin Manager: Parse ODM data 0x000a4000 [0004.426] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70 006000 [0004.434] Add serial number:1424121072650 as DT property [0004.443] "bpmp" doesn't exist, creating [0004.449] Updated bpmp info to DTB [0004.454] Updated initrd info to DTB [0004.457] "proc-board" doesn't exist, creating [0004.463] Updated board info to DTB [0004.466] "pmu-board" doesn't exist, creating [0004.472] Updated board info to DTB [0004.476] "display-board" doesn't exist, creating [0004.482] Updated board info to DTB [0004.485] "reset" doesn't exist, creating [0004.490] Updated reset info to DTB [0004.493] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype= 0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@6 3 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lspor t,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 l p0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800 000@0x92ca9000 is_hdmi_initialised=1 [0004.532] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0004.538] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 c onsole=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0004.551] Updated bootarg info to DTB [0004.555] Adding uuid 000000016430b7440000000003fd8240 to DT [0004.561] Adding eks info 0 to DT [0004.566] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.572] Updated memory info to DTB [0004.580] set vdd_core voltage to 1075 mv [0004.584] setting 'vdd-core' regulator to 1075000 micro volts [0004.590] Found secure-pmc; disable BPMP U-Boot 2020.04-g6b630d64fd (Feb 19 2021 - 08:37:46 -0800) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 1181 bytes read in 27 ms (42 KiB/s) L4T boot options 1: primary kernel 2: MCP251x CAN Controller Enter choice: 2: MCP251x CAN Controller Retrieving file: /boot/initrd 7159841 bytes read in 336 ms (20.3 MiB/s) Retrieving file: /boot/Image 34338824 bytes read in 1502 ms (21.8 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 Retrieving file: /boot/kernel_tegra210-p3448-0000-p3449-0000-b00-mcp251x-can-controller.dtb 244955 bytes read in 35 ms (6.7 MiB/s) ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083000000, end 000000008303ecda copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... DT property /chosen/nvidia,bluetooth-mac missing in source; can't copy DT property /chosen/nvidia,wifi-mac missing in source; can't copy DT property /psci/nvidia,system-lp0-disable missing in source; can't copy Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (buildbrain@mobile-u64-5294-d8000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Feb 19 08:40:32 PST 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29364(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3560360K/4159488K available (15294K kernel code, 2942K rwdata, 6664K rodata, 8576K init, 609K bss, 123992K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009600000 ( 6720 KB) [ 0.000000] .init : 0xffffff8009600000 - 0xffffff8009e60000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e60000 - 0xffffff800a13f808 ( 2943 KB) [ 0.000000] .bss : 0xffffff800a13f808 - 0xffffff800a1d7cbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.010097] Console: colour dummy device 80x25 [ 0.014749] console [tty0] enabled [ 0.018259] bootconsole [uart8250] disabled [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (buildbrain@mobile-u64-5294-d8000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Feb 19 08:40:32 PST 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29364(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3560360K/4159488K available (15294K kernel code, 2942K rwdata, 6664K rodata, 8576K init, 609K bss, 123992K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009600000 ( 6720 KB) [ 0.000000] .init : 0xffffff8009600000 - 0xffffff8009e60000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e60000 - 0xffffff800a13f808 ( 2943 KB) [ 0.000000] .bss : 0xffffff800a13f808 - 0xffffff800a1d7cbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.010097] Console: colour dummy device 80x25 [ 0.014749] console [tty0] enabled [ 0.018259] bootconsole [uart8250] disabled [ 0.022583] kmemleak: Kernel memory leak detector disabled [ 0.022612] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.022634] pid_max: default: 32768 minimum: 301 [ 0.023097] Security Framework initialized [ 0.023322] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.023339] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.024538] ftrace: allocating 47208 entries in 185 pages [ 0.194870] ASID allocator initialised with 65536 entries [ 0.232718] tegra-id: chipid=22117. [ 0.232748] tegra-id: opt_subrevision=0. [ 0.232773] Tegra Speedo/IDDQ fuse revision 4 [ 0.232782] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.232792] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0 [ 0.232803] Tegra: CPU Speedo Value 2117, SoC Speedo Value 1997, GPU Speedo Value 2124 [ 0.232813] Tegra: CPU IDDQ Value 2316, SoC IDDQ Value 2360, GPU IDDQ Value 3120 [ 0.232839] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1 [ 0.232863] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.232883] DTB Build time: Feb 19 2021 08:42:41 [ 0.281323] CPU1: Booted secondary processor [411fd071] [ 0.313241] CPU2: Booted secondary processor [411fd071] [ 0.345214] CPU3: Booted secondary processor [411fd071] [ 0.345313] Brought up 4 CPUs [ 0.345372] SMP: Total of 4 processors activated. [ 0.345390] CPU features: detected feature: 32-bit EL0 Support [ 0.345665] CPU: All CPU(s) started at EL2 [ 0.345693] alternatives: patching kernel code [ 0.354165] devtmpfs: initialized [ 0.394297] Initilizing CustomIPI irq domain [ 0.394724] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.394769] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.406328] pinctrl core: initialized pinctrl subsystem [ 0.406995] OS set in device tree is not L4T. [ 0.407477] regulator-dummy: no parameters [ 0.407756] Initializing plugin-manager [ 0.407926] Plugin module not found [ 0.408128] node /plugin-manager/fragement@0 match with board >=3448-0000-100 [ 0.408733] node /plugin-manager/fragment@1 match with board >=3448-0000-101 [ 0.409790] node /plugin-manager/fragement@7 match with odm-data enable-pmic-wdt [ 0.410035] node /plugin-manager/fragement@8 match with odm-data enable-pmic-wdt [ 0.410665] node /plugin-manager/fragement@10 match with board >=3448-0000-300 [ 0.412632] node /plugin-manager/fragement@13 match with board >=3448-0000-300 [ 0.416523] NET: Registered protocol family 16 [ 0.417877] pstore: using zlib compression [ 0.418410] console [pstore-1] enabled [ 0.418426] pstore: Registered ramoops as persistent store backend [ 0.418444] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.433341] cpuidle: using governor menu [ 0.436991] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.439068] vdso: 2 pages (1 code @ ffffff8008f77000, 1 data @ ffffff8009e64000) [ 0.439115] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.441832] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.444444] Serial: AMBA PL011 UART driver [ 0.444985] tegra_powergate_init: DONE [ 0.445017] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.445052] DTB Build time: Feb 19 2021 08:42:41 [ 0.447293] Tegra reboot handler registered. [ 0.452070] iommu: Adding device tegra-carveouts to group 0 [ 0.452241] platform tegra-carveouts: domain=ffffffc0f946c3d8 allocates as[0]=ffffffc0f94380a8 [ 0.452628] iommu: Adding device smmu_test to group 1 [ 0.452695] platform smmu_test: domain=ffffffc0f946c618 allocates as[0]=ffffffc0f9438110 [ 0.453591] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000 [ 0.453664] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000 [ 0.453730] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000 [ 0.453751] nv-tegra-mc 70019000.mc: No mssnvlink node [ 0.453788] mc-err: mcerr ops are set to t21x [ 0.461608] iommu: Adding device 70090000.xusb to group 2 [ 0.461937] iommu: Adding device 70006000.serial to group 3 [ 0.462033] platform 70006000.serial: domain=ffffffc0f9b886d8 allocates as[0]=ffffffc0f9438178 [ 0.462506] iommu: Adding device 70006040.serial to group 4 [ 0.462794] iommu: Adding device 70006200.serial to group 5 [ 0.463038] iommu: Adding device sound to group 6 [ 0.463102] platform sound: domain=ffffffc0f9b88c18 allocates as[0]=ffffffc0f94381e0 [ 0.463711] iommu: Adding device 7000d400.spi to group 7 [ 0.463997] iommu: Adding device 7000d600.spi to group 8 [ 0.464284] iommu: Adding device 70410000.spi to group 9 [ 0.464615] iommu: Adding device 50000000.host1x to group 10 [ 0.464920] iommu: Adding device 54080000.vi to group 11 [ 0.465447] iommu: Adding device 54600000.isp to group 12 [ 0.465743] iommu: Adding device 54680000.isp to group 13 [ 0.466081] iommu: Adding device tegradc.0 to group 14 [ 0.466150] platform tegradc.0: domain=ffffffc0f94e0b58 allocates as[0]=ffffffc0f9438248 [ 0.470356] platform tegradc.0: IOVA linear map 0x0000000092ca9000(800000) [ 0.470767] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [ 0.471125] iommu: Adding device tegradc.1 to group 15 [ 0.471188] platform tegradc.1: domain=ffffffc0f94e0d98 allocates as[0]=ffffffc0f94382b0 [ 0.475368] platform tegradc.1: IOVA linear map 0x0000000092ca9000(800000) [ 0.475771] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [ 0.476040] iommu: Adding device 54340000.vic to group 16 [ 0.476263] iommu: Adding device 544c0000.nvenc to group 17 [ 0.476486] iommu: Adding device 54500000.tsec to group 18 [ 0.476700] iommu: Adding device 54100000.tsecb to group 19 [ 0.476915] iommu: Adding device 54480000.nvdec to group 20 [ 0.477150] iommu: Adding device 54380000.nvjpg to group 21 [ 0.478280] iommu: Adding device 546c0000.i2c to group 22 [ 0.478634] iommu: Adding device 57000000.gpu to group 23 [ 0.478703] platform 57000000.gpu: domain=ffffffc0f94eed98 allocates as[0]=ffffffc0f9438318 [ 0.478756] platform 57000000.gpu: domain=ffffffc0f94eed98 allocates as[1]=ffffffc0f9438380 [ 0.478815] platform 57000000.gpu: domain=ffffffc0f94eed98 allocates as[2]=ffffffc0f94383e8 [ 0.478871] platform 57000000.gpu: domain=ffffffc0f94eed98 allocates as[3]=ffffffc0f9438450 [ 0.479815] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.479853] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.479879] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET [ 0.479898] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [ 0.479914] tegra-pmc: ### PMC reset status reg: 0x0 [ 0.529419] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.529453] tegra-pmc: Clear bootloader IO dpd settings [ 0.529485] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.529571] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.529891] iommu: Adding device 70012000.se to group 24 [ 0.530758] iommu: Adding device 7000c000.i2c to group 25 [ 0.531036] iommu: Adding device 7000c400.i2c to group 26 [ 0.531364] iommu: Adding device 7000c500.i2c to group 27 [ 0.531629] iommu: Adding device 7000c700.i2c to group 28 [ 0.531991] iommu: Adding device 7000d000.i2c to group 29 [ 0.532260] iommu: Adding device 7000d100.i2c to group 30 [ 0.532623] iommu: Adding device sdhci-tegra.0 to group 31 [ 0.532693] platform sdhci-tegra.0: domain=ffffffc0f957af18 allocates as[0]=ffffffc0f94384b8 [ 0.533625] iommu: Adding device 700d0000.xudc to group 32 [ 0.537402] vdd-ac-bat: 5000 mV [ 0.537816] vdd-5v0-sys: 5000 mV [ 0.538905] vdd-5v0-hdmi: supplied by vdd-5v0-sys [ 0.539000] vdd-5v0-hdmi: 5000 mV [ 0.539496] vdd-1v8-sys: 1800 mV [ 0.539897] vdd-fan: supplied by vdd-5v0-sys [ 0.539950] vdd-fan: 5000 mV [ 0.540336] vdd-usb-vbus: supplied by vdd-5v0-sys [ 0.540409] vdd-usb-vbus: 5000 mV [ 0.540977] vdd-usb-vbus2: 5000 mV [ 0.574385] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.576958] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [ 0.578682] GPIO line 151 (camera-control-output-low) hogged as output/low [ 0.578723] GPIO line 152 (camera-control-output-low) hogged as output/low [ 0.578775] GPIO line 6 (system-suspend-gpio) hogged as output/high [ 0.579165] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [ 0.587517] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.587913] SCSI subsystem initialized [ 0.588457] usbcore: registered new interface driver usbfs [ 0.588531] usbcore: registered new interface driver hub [ 0.588622] usbcore: registered new device driver usb [ 0.592795] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.595018] random: fast init done [ 0.596586] vdd-core: 600 <--> 1162 mV at 1075 mV [ 0.597674] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [ 0.600474] vdd-ddr-1v1: 1150 mV [ 0.604633] vdd-pre-reg-1v35: 1350 mV [ 0.608474] vdd-1v8: 1800 mV [ 0.612470] avdd-sys-1v2: 1200 mV [ 0.616469] vdd-pex-1v0: 1050 mV [ 0.617170] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [ 0.617740] max77620-ldo3: at 3100 mV [ 0.620477] vdd-rtc: 850 <--> 1100 mV at 1000 mV [ 0.621042] max77620-ldo5: at 3100 mV [ 0.624471] vddio-sdmmc3-ap: 1800 <--> 3300 mV at 2800 mV [ 0.628491] avdd-1v05-pll: 1050 mV [ 0.632470] avdd-io-hdmi-dp: 1050 mV [ 0.635138] GPIO line 505 (spmic-default-output-high) hogged as output/high [ 0.635492] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [ 0.635808] max77620 4-003c: max77620 probe successful [ 0.638640] media: Linux media interface: v0.10 [ 0.638718] Linux video capture interface: v2.00 [ 0.639733] pps_core: LinuxPPS API ver. 1 registered [ 0.639759] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.639804] PTP clock support registered [ 0.643278] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [ 0.644202] Advanced Linux Sound Architecture Driver Initialized. [ 0.644894] Bluetooth: Core ver 2.22 [ 0.644966] NET: Registered protocol family 31 [ 0.644983] Bluetooth: HCI device and connection manager initialized [ 0.645010] Bluetooth: HCI socket layer initialized [ 0.645030] Bluetooth: L2CAP socket layer initialized [ 0.645069] Bluetooth: SCO socket layer initialized [ 0.646958] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.646993] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.647055] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.647082] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.651123] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.652394] vdd-3v3-sys: supplied by vdd-5v0-sys [ 0.652569] vdd-3v3-sys: 3300 mV [ 0.652911] vdd-1v8-sys: supplied by vdd-3v3-sys [ 0.656558] vdd-usb-vbus2: supplied by vdd-3v3-sys [ 0.657056] vdd-3v3-sd: supplied by vdd-3v3-sys [ 0.657106] vdd-3v3-sd: 3300 mV [ 0.658205] avdd-io-edp-1v05: supplied by avdd-1v05-pll [ 0.658283] avdd-io-edp-1v05: 1050 mV [ 0.658744] vdd-usb-hub-en: supplied by vdd-1v8-sys [ 0.658794] vdd-usb-hub-en: 5000 mV [ 0.660206] camchar: rtcpu character device driver loaded [ 0.661074] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0 [ 0.662378] clocksource: Switched to clocksource arch_sys_counter [ 0.703689] VFS: Disk quotas dquot_6.6.0 [ 0.703864] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.704376] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.704819] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [ 0.704869] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [ 0.705094] cma: enabled page replacement for spfn=d7000, epfn=f0000 [ 0.705118] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.705144] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.705190] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.705215] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.705247] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [ 0.705268] nvmap_page_pool_init: Total RAM pages: 1008874 [ 0.705285] nvmap_page_pool_init: nvmap page pool size: 126109 pages (492 MB) [ 0.705388] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.705865] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.706877] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [ 0.715385] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.715902] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.716308] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.716621] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.716812] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.717122] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.717142] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB [ 0.717595] NET: Registered protocol family 2 [ 0.718639] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.718877] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.719436] TCP: Hash tables configured (established 32768 bind 32768) [ 0.719622] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.719720] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.720170] NET: Registered protocol family 1 [ 0.720928] RPC: Registered named UNIX socket transport module. [ 0.720954] RPC: Registered udp transport module. [ 0.720970] RPC: Registered tcp transport module. [ 0.720985] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.721259] Trying to unpack rootfs image as initramfs... [ 1.026355] Freeing initrd memory: 6992K [ 1.037001] host1x 50000000.host1x: initialized [ 1.038913] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.042223] audit: initializing netlink subsys (disabled) [ 1.042360] audit: type=2000 audit(0.883:1): initialized [ 1.043179] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 1.053128] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.054744] ntfs: driver 2.1.32 [Flags: R/W]. [ 1.055567] 9p: Installing v9fs 9p2000 file system support [ 1.058865] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 1.059075] io scheduler noop registered [ 1.059374] io scheduler cfq registered (default) [ 1.062097] gic 702f9000.agic: GIC IRQ controller registered [ 1.065549] iommu: Adding device 702ef000.adsp to group 33 [ 1.074571] iommu: Adding device aconnect@702c0000:adsp_audio to group 34 [ 1.074753] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [ 1.075422] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x8247c0f [ 1.075454] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [ 1.077177] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [ 1.077324] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [ 1.077437] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [ 1.077650] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [ 1.077763] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [ 1.077870] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [ 1.077973] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [ 1.078089] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [ 1.078191] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [ 1.078298] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [ 1.084517] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 1.086306] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 1.088307] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.089621] tegra-pcie 1003000.pcie: PCIE: Enable power rails [ 1.090003] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.091321] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 1.091582] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [ 1.091857] Adding domain tsec-pd to PM domain host1x-pd [ 1.094449] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 1.095457] tsec 54500000.tsec: initialized [ 1.097053] tsec 54100000.tsecb: initialized [ 1.097819] Adding domain nvdec-pd to PM domain host1x-pd [ 1.101631] nvdec 54480000.nvdec: initialized [ 1.102832] Adding domain vic03-pd to PM domain host1x-pd [ 1.103039] Adding domain msenc-pd to PM domain host1x-pd [ 1.103214] Adding domain nvjpg-pd to PM domain host1x-pd [ 1.107777] falcon 54340000.vic: initialized [ 1.109130] falcon 544c0000.nvenc: initialized [ 1.110506] falcon 54380000.nvjpg: initialized [ 1.115022] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=97 [ 1.115105] tegra_cec 70015000.tegra_cec: Enable clock result: 0. [ 1.115152] tegra_cec 70015000.tegra_cec: tegra_cec_init started [ 1.115293] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [ 1.115413] display board info: id 0x0, fab 0x0 [ 1.115441] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0 [ 1.115460] tegra_cec 70015000.tegra_cec: probed [ 1.115486] generic_infoframe_type: 0x87 [ 1.115657] tegradc tegradc.0: DT parsed successfully [ 1.115717] tegradc tegradc.0: Display dc.ffffff800ab80000 registered with id=0 [ 1.116288] tegradc tegradc.0: Bootloader disp_param detected. Detected mode: 1920x1080 (on 0x0mm) pclk=148350781 [ 1.119901] tegradc tegradc.0: probed [ 1.125627] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.132527] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels [ 1.133563] tegra-fuse-burn 7000f800.efuse:efuse-burn: shutdown limit check disabled [ 1.133598] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 1.133959] kfuse 7000fc00.kfuse: initialized [ 1.135653] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [ 1.136760] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 1.138297] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 1.138342] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 1.138853] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 1.140687] vdd-gpu: applied init 1000000uV constraint [ 1.140725] vdd-gpu: 708 <--> 1323 mV at 997 mV [ 1.141166] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 1.146018] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.146229] No Device Node present for smmu client: serial8250 !! [ 1.146262] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.146340] iommu: Adding device serial8250 to group 35 [ 1.148765] console [ttyS0] disabled [ 1.148912] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [ 1.613633] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.018189] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.146405] tegra_cec 70015000.tegra_cec: Can't find physical addresse. [ 2.146410] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [ 2.422058] tegra-pcie 1003000.pcie: link 0 down, retrying [ 2.424077] tegra-pcie 1003000.pcie: link 0 down, ignoring [ 2.530289] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 2.530301] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.530306] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 2.530312] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 2.530317] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.530753] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.542530] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff] [ 2.542535] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [ 2.542546] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff 64bit] [ 2.542567] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff 64bit] [ 2.542585] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.542596] pci 0000:00:02.0: PCI bridge to [bus 01] [ 2.542601] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 2.542608] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] [ 2.542995] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 2.543000] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 3.612199] console [ttyS0] enabled [ 3.612800] Console: switching to colour frame buffer device 240x67 [ 3.615706] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [ 3.616050] serial-tegra 70006200.serial: RX in PIO mode [ 3.616146] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART [ 3.617241] [drm] Initialized [ 3.649450] tegradc tegradc.0: fb registered [ 3.653069] brd: module loaded [ 3.661249] loop: module loaded [ 3.664019] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_mode. [ 3.664065] tegradc tegradc.0: hdmi: tmds rate:148351K prod-setting:prod_c_hdmi_75m_150m [ 3.664566] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by BL. [ 3.664576] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by BL. [ 3.694573] tegra_profiler: version: 1.143, samples/io: 48/28 [ 3.694668] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 3.694671] Extcon AUX1(HDMI) enable [ 3.695673] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [ 3.695754] tegradc tegradc.1: No lt-data, using default setting [ 3.695780] tegradc tegradc.1: No hpd-gpio in DT [ 3.695811] tegradc tegradc.1: DT parsed successfully [ 3.695872] tegradc tegradc.1: Display dc.ffffff800d500000 registered with id=1 [ 3.697307] tegradc tegradc.1: dpd enable lookup fail:-19 [ 3.728942] tegradc tegradc.0: nominal-pclk:148351648 parent:148350781 div:1.0 pclk:148350781 146868084~161703244 [ 3.732589] tegradc tegradc.1: probed [ 3.758739] tegradc tegradc.1: fb registered [ 3.763080] tegra_profiler: auth: init [ 3.766185] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1 [ 3.766189] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset) [ 3.766196] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0 [ 3.787303] tegradc tegradc.1: blank - powerdown [ 3.787777] THERMAL EST: found 2 subdevs [ 3.787781] THERMAL EST num_resources: 0 [ 3.787785] [THERMAL EST subdev 0] [ 3.787789] [THERMAL EST subdev 1] [ 3.788098] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 3.788100] THERMAL EST: thz register success. [ 3.788291] THERMAL EST: end of probe, return err: 0 [ 3.788905] sd: No Scsi addr parsed to reserve index [ 3.788925] hisi_sas: driver version v1.6 [ 3.792612] tegra-qspi 70410000.spi: Prod settings list not found [ 3.793416] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes) [ 3.793422] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0 [ 3.797400] libphy: Fixed MDIO Bus: probed [ 3.797929] tun: Universal TUN/TAP device driver, 1.6 [ 3.797931] tun: (C) 1999-2004 Max Krasnyansky [ 3.802961] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 3.802963] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.803010] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 3.803011] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.803053] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 3.803055] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 3.803094] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [ 3.803096] Copyright(c) 1999 - 2017 Intel Corporation. [ 3.803737] r8168 0000:01:00.0: enabling device (0000 -> 0003) [ 3.803756] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 3.818182] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [ 3.818243] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 48:b0:2d:5b:a9:c2 from device tree [ 3.818858] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 3.818888] r8168 Copyright (C) 2017 Realtek NIC software team [ 3.818888] This program comes with ABSOLUTELY NO WARRANTY; for details, please see . [ 3.818888] This is free software, and you are welcome to redistribute it under certain conditions; see . [ 3.819316] PPP generic driver version 2.4.2 [ 3.819454] PPP BSD Compression module registered [ 3.819457] PPP Deflate Compression module registered [ 3.819471] PPP MPPE Compression module registered [ 3.819475] NET: Registered protocol family 24 [ 3.819516] usbcore: registered new interface driver r8152 [ 3.819553] usbcore: registered new interface driver asix [ 3.819586] usbcore: registered new interface driver ax88179_178a [ 3.819613] usbcore: registered new interface driver cdc_ether [ 3.819639] usbcore: registered new interface driver net1080 [ 3.819667] usbcore: registered new interface driver cdc_subset [ 3.819693] usbcore: registered new interface driver zaurus [ 3.819737] usbcore: registered new interface driver cdc_ncm [ 3.822110] VFIO - User Level meta-driver version: 0.3 [ 3.823114] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.823124] ehci-pci: EHCI PCI platform driver [ 3.823156] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.823162] ohci-pci: OHCI PCI platform driver [ 3.823192] ohci-platform: OHCI generic platform driver [ 3.825109] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [ 3.827642] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [ 3.828707] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f96d5c00 id [ 3.829736] usbcore: registered new interface driver uas [ 3.829779] usbcore: registered new interface driver usb-storage [ 3.829844] usbcore: registered new interface driver usbserial [ 3.832885] tegra-xudc-new 700d0000.xudc: device count: 1 [ 3.833898] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 3.833908] tegra-xudc-new 700d0000.xudc: vbus state: 0 [ 3.833931] tegra-xudc-new 700d0000.xudc: entering ELPG [ 3.834171] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 3.834397] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release [ 3.834427] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.834443] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [ 3.835159] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [ 3.835192] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [ 3.835342] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.835347] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.835352] usb usb1: Product: xHCI Host Controller [ 3.835355] usb usb1: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 3.835359] usb usb1: SerialNumber: 70090000.xusb [ 3.835760] hub 1-0:1.0: USB hub found [ 3.835794] hub 1-0:1.0: 5 ports detected [ 3.836261] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.836270] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [ 3.836346] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.836456] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 3.836461] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.836465] usb usb2: Product: xHCI Host Controller [ 3.836468] usb usb2: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 3.836471] usb usb2: SerialNumber: 70090000.xusb [ 3.842628] hub 2-0:1.0: USB hub found [ 3.842629] mousedev: PS/2 mouse device common for all mice [ 3.842660] hub 2-0:1.0: 4 ports detected [ 3.842696] usbcore: registered new interface driver xpad [ 3.843519] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [ 3.843524] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [ 3.938431] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1 [ 3.946604] usb usb2: usb_suspend_both: status 0 [ 3.971257] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 3.973352] rtc rtc1: alarm rtc device [ 3.973364] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 3.973381] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 3.973749] i2c /dev entries driver [ 3.975340] i2c i2c-6: Added multiplexed i2c bus 7 [ 3.975725] i2c i2c-6: Added multiplexed i2c bus 8 [ 3.975730] i2c-mux-gpio cam_i2cmux: 2 port mux on Tegra I2C adapter adapter [ 3.976311] imx219 7-0010: tegracam sensor driver:imx219_v2.0.6 [ 3.999590] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 3.999659] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 3.999725] imx219 7-0010: board setup failed [ 3.999774] imx219: probe of 7-0010 failed with error -121 [ 4.000202] imx219 8-0010: tegracam sensor driver:imx219_v2.0.6 [ 4.023463] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 4.023537] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 4.023598] imx219 8-0010: board setup failed [ 4.023647] imx219: probe of 8-0010 failed with error -121 [ 4.024455] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 4.026596] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 4.026601] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [ 4.026903] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.026916] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 4.026923] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 4.027054] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.027063] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 4.027069] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 4.027221] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.027229] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 4.027234] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 4.027411] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 4.027950] tegra_aotag tegra-aotag: Registering sensor 0 [ 4.027995] tegra_aotag tegra-aotag: Invalid temp readout [ 4.028014] tegra_aotag tegra-aotag: Invalid temp readout [ 4.028029] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 4.028037] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 4.028897] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.028911] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 4.029093] tegra_aotag tegra-aotag: Invalid temp readout [ 4.029116] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 4.029503] parse_throttle_dt_data: Num cap clks = 6 [ 4.029508] parse_throttle_dt_data: clk=cclk_g type=2 [ 4.029514] parse_throttle_dt_data: clk=gpu type=4 [ 4.029534] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 4.029555] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 4.029578] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 4.029581] parse_throttle_dt_data: clk=emc type=3 [ 4.029873] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.029964] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.030101] tegra_throttle_probe: probe successful. #cdevs=4 [ 4.030781] FAN dev name: pwm-fan [ 4.030822] FAN:gpio request success. [ 4.030873] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 4.031105] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 4.031218] pwm_fan_driver pwm-fan: fan tach request irq success [ 4.031224] pwm_fan_driver pwm-fan: tach period: 1000 [ 4.031296] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 4.031301] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 4.031306] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 4.031310] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 4.031314] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 4.031318] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 4.031322] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 4.031325] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 4.031329] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 4.031333] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 4.033804] device-mapper: uevent: version 1.0.3 [ 4.034266] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 4.037076] tegra210-cpufreq cpufreq: probe()...completed [ 4.037912] sdhci: Secure Digital Host Controller Interface driver [ 4.037914] sdhci: Copyright(c) Pierre Ossman [ 4.037915] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.038426] sdhci-tegra sdhci-tegra.0: Got CD GPIO [ 4.038785] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful [ 4.038909] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300 [ 4.044246] tegra-se 70012000.se: tegra_se_probe: complete [ 4.044812] hidraw: raw HID events driver (C) Jiri Kosina [ 4.046683] usbcore: registered new interface driver usbhid [ 4.046685] usbhid: USB HID core driver [ 4.048853] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 4.049020] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 4.050939] nvpmodel: initialized successfully [ 4.052100] usbcore: registered new interface driver snd-usb-audio [ 4.052157] No Device Node present for smmu client: snd-soc-dummy !! [ 4.052162] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 4.052179] iommu: Adding device snd-soc-dummy to group 36 [ 4.072636] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0 [ 4.079836] OPE platform probe [ 4.079922] OPE platform probe successful [ 4.080201] OPE platform probe [ 4.080279] OPE platform probe successful [ 4.090543] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr [ 4.110818] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 4.110948] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 4.111076] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 4.111200] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 4.111321] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 4.111441] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 4.111564] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 4.111685] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 4.111806] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 4.111926] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 4.125616] u32 classifier [ 4.125617] Actions configured [ 4.125688] Initializing XFRM netlink socket [ 4.126406] NET: Registered protocol family 10 [ 4.127172] NET: Registered protocol family 17 [ 4.127182] NET: Registered protocol family 15 [ 4.127257] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 4.127354] Bluetooth: RFCOMM socket layer initialized [ 4.127363] Bluetooth: RFCOMM ver 1.11 [ 4.127367] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.127374] Bluetooth: HIDP socket layer initialized [ 4.127392] 9pnet: Installing 9P2000 support [ 4.127429] Key type dns_resolver registered [ 4.128886] Registered cp15_barrier emulation handler [ 4.128939] Registered setend emulation handler [ 4.129997] registered taskstats version 1 [ 4.130617] Adding domain ve2-pd to PM domain host1x-pd [ 4.130856] Adding domain ve-pd to PM domain host1x-pd [ 4.132950] isp 54600000.isp: initialized [ 4.133869] isp 54680000.isp: initialized [ 4.144214] last reset is due to power on reset [ 4.144217] KERNEL: PMC reset status reg: 0x0 [ 4.144279] BL: PMC reset status reg: 0x0 [ 4.144281] BL: PMIC poweroff Event Recorder: 0x50 [ 4.145808] clk_cbus_recalc_rate: no gbus parent [ 4.145812] clk_cbus_round_rate: no gbus parent [ 4.145813] clk_cbus_round_rate: no gbus parent [ 4.145820] clk_cbus_recalc_rate: no gbus parent [ 4.145921] clk_cbus_recalc_rate: no gbus parent [ 4.145924] clk_cbus_round_rate: no gbus parent [ 4.145925] clk_cbus_round_rate: no gbus parent [ 4.145928] clk_cbus_recalc_rate: no gbus parent [ 4.146640] tegra_dvfs: GPU-cap: registered [ 4.146697] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [ 4.146699] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled [ 4.146701] tegra dvfs: vdd-gpu: nominal 1038mV, offset 708000uV, step 10000uV, scaling enabled [ 4.148090] tegra_dvfs: vdd-gpu-vts: registered [ 4.148839] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 4.149463] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 4.149971] input: gpio-keys as /devices/gpio-keys/input/input1 [ 4.166444] usb 1-2: new high-speed USB device number 2 using tegra-xusb [ 4.184069] tegra_rtc 7000e000.rtc: setting system clock to 2022-04-26 11:39:15 UTC (1650973155) [ 4.185136] vi 54080000.vi: vi_probe: ++ [ 4.199206] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411 [ 4.199210] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.199213] usb 1-2: Product: USB2.1 Hub [ 4.199215] usb 1-2: Manufacturer: Generic [ 4.201417] hub 1-2:1.0: USB hub found [ 4.201829] vi 54080000.vi: initialized [ 4.202456] hub 1-2:1.0: 5 ports detected [ 4.208291] vi 54080000.vi: subdev nvcsi--2 bound [ 4.208397] vi 54080000.vi: subdev nvcsi--1 bound [ 4.209203] Disable partitions left on by BL [ 4.209206] disb [ 4.209248] bwmgr: missing cdev-type property [ 4.209335] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.209341] DRAM derating cdev registered. [ 4.210344] ALSA device list: [ 4.210346] #0: tegra-hda at 0x70038000 irq 83 [ 4.210348] #1: tegra-snd-t210ref-mobile-rt565x [ 4.297111] mmc0: hw tuning done ... [ 4.297143] mmc0: new ultra high speed SDR104 SDXC card at address aaaa [ 4.297534] mmcblk0: mmc0:aaaa SD64G 59.5 GiB [ 4.302991] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 [ 4.322799] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.354134] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411 [ 4.354138] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.354141] usb 2-1: Product: USB3.2 Hub [ 4.354143] usb 2-1: Manufacturer: Generic [ 4.355130] hub 2-1:1.0: USB hub found [ 4.355871] hub 2-1:1.0: 4 ports detected [ 4.502433] usb 1-2.1: new high-speed USB device number 3 using tegra-xusb [ 4.506382] usb 2-1: usb_suspend_both: status 0 [ 4.506525] usb usb2: usb_suspend_both: status 0 [ 4.523325] usb 1-2.1: New USB device found, idVendor=0bda, idProduct=8179 [ 4.523329] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.523331] usb 1-2.1: Product: 802.11n NIC [ 4.523334] usb 1-2.1: Manufacturer: Realtek [ 4.523336] usb 1-2.1: SerialNumber: 00E04C0001 [ 4.606434] usb 1-2.3: new full-speed USB device number 4 using tegra-xusb [ 4.630257] usb 1-2.3: New USB device found, idVendor=046d, idProduct=c534 [ 4.630260] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.630263] usb 1-2.3: Product: USB Receiver [ 4.630265] usb 1-2.3: Manufacturer: Logitech [ 4.633153] input: Logitech USB Receiver as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.0/0003:046D:C534.0001/input/input2 [ 4.694929] hid-generic 0003:046D:C534.0001: input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-70090000.xusb-2.3/input0 [ 4.698055] input: Logitech USB Receiver as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.1/0003:046D:C534.0002/input/input3 [ 4.754925] hid-generic 0003:046D:C534.0002: input,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-70090000.xusb-2.3/input1 [ 5.470085] extcon-disp-state extcon:disp-state: cable 44 state 0 already set. [ 5.470086] Extcon DP: HPD disabled [ 5.470088] hpd: hpd_switch 0 [ 5.470091] hpd: switching from state 0 (Reset) to state 1 (Check Plug) [ 5.470107] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [ 5.470111] hpd: switching from state 1 (Check Plug) to state 3 (Disabled) [ 5.470156] tegradc tegradc.0: blank - powerdown [ 5.513530] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 5.513532] Extcon AUX1(HDMI) disable [ 5.541499] tegradc tegradc.0: unblank [ 5.551899] tegradc tegradc.0: nominal-pclk:174500000 parent:174498750 div:1.0 pclk:174498750 172755000~190205000 [ 5.551947] tegradc tegradc.0: hdmi: tmds rate:174500K prod-setting:prod_c_hdmi_150m_300m [ 5.552938] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 5.587728] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 5.587729] Extcon AUX1(HDMI) enable [ 5.593198] tegradc tegradc.0: sync windows ret = 249 [ 5.736659] extcon-disp-state extcon:disp-state: cable 51 state 1 [ 5.736661] Extcon HDMI: HPD enabled [ 5.736671] tegradc tegradc.0: hdmi: plugged [ 5.759726] Freeing unused kernel memory: 8576K [ 5.790398] Root device found: mmcblk0p1 [ 5.797793] Found dev node: /dev/mmcblk0p1 [ 6.508237] EXT4-fs (mmcblk0p1): 17 orphan inodes deleted [ 6.515652] EXT4-fs (mmcblk0p1): recovery complete [ 6.551771] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 6.563721] Rootfs mounted over mmcblk0p1 [ 6.588252] Switching from initrd to actual rootfs [ 6.788308] ip_tables: (C) 2000-2006 Netfilter Core Team [ 6.807633] cgroup: cgroup2: unknown option "nsdelegate" [ 6.837256] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 6.863575] systemd[1]: Detected architecture arm64. [ 6.903099] systemd[1]: Set hostname to . [ 7.021499] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 7.040899] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 7.202395] random: systemd: uninitialized urandom read (16 bytes read) [ 7.211470] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 7.223772] random: systemd: uninitialized urandom read (16 bytes read) [ 7.234195] systemd[1]: Created slice System Slice. [ 7.243744] random: systemd: uninitialized urandom read (16 bytes read) [ 7.253432] systemd[1]: Created slice system-remoteit.slice. [ 7.263925] systemd[1]: Listening on RPCbind Server Activation Socket. [ 7.275969] systemd[1]: Created slice User and Session Slice. [ 7.398674] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [ 7.464447] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1268 [INFO] GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1) [ 7.501325] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 7.501343] cpu-throttle-alert cooling device registered. [ 7.501472] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 7.501485] gpu-throttle-alert cooling device registered. [ 7.501638] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 7.501650] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 7.501661] hot-surface-alert cooling device registered. [ 8.566391] random: crng init done [ 8.571317] random: 7 urandom warning(s) missed due to ratelimiting [ 9.218583] using random self ethernet address [ 9.234159] using random host ethernet address [ 9.874602] mcp251x spi0.0: MCP251x didn't enter in conf mode after reset [ 9.889012] mcp251x spi0.0: Probe failed, err=16 [ 9.889030] mcp251x: probe of spi0.0 failed with error -16 [ 10.415266] using random self ethernet address [ 10.438418] using random host ethernet address [ 10.961842] mcp251x spi1.0: MCP251x didn't enter in conf mode after reset [ 11.085239] mcp251x spi1.0: Probe failed, err=16 [ 11.303178] mcp251x: probe of spi1.0 failed with error -16 [ 12.692561] r8188eu: module is from the staging directory, the quality is unknown, you have been warned. Ubuntu 18.04.5 LTS jetson-desktop ttyS0 jetson-desktop login: jetson Password: Last login: Wed Apr 20 16:06:38 IST 2022 from 127.0.0.1 on pts/1 Welcome to Ubuntu 18.04.5 LTS (GNU/Linux 4.9.201-tegra aarch64) * Documentation: https://help.ubuntu.com * Management: https://landscape.canonical.com * Support: https://ubuntu.com/advantage This system has been minimized by removing packages and content that are not required on a system that users do not log into. To restore this content, you can run the 'unminimize' command. 394 packages can be updated. 268 updates are security updates. ADMS_D2200001 jetson@jetson-desktop:~$