Rebooting system ... �� [0000.053] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses. [0000.062] I> MB1 (prd-version: 1.5.1.7-t194-41334769-98030a79) [0000.067] I> Boot-mode: Coldboot [0000.070] I> Chip revision : A02P [0000.073] I> Bootrom patch version : 15 (correctly patched) [0000.078] I> ATE fuse revision : 0x200 [0000.082] I> Ram repair fuse : 0x0 [0000.085] I> Ram Code : 0x2 [0000.088] I> rst_source : 0xb [0000.090] I> rst_level : 0x1 [0000.094] I> Boot-device: eMMC [0000.109] I> sdmmc DDR50 mode [0000.113] W> No valid slot number is found in scratch register [0000.118] W> Return default slot: _a [0000.122] I> Active Boot chain : 0 [0000.125] I> Boot-device: eMMC [0000.128] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0000.135] I> Temperature = 39000 [0000.138] W> Skipping boost for clk: BPMP_CPU_NIC [0000.142] W> Skipping boost for clk: BPMP_APB [0000.146] W> Skipping boost for clk: AXI_CBB [0000.150] W> Skipping boost for clk: AON_CPU_NIC [0000.154] W> Skipping boost for clk: CAN1 [0000.158] W> Skipping boost for clk: CAN2 [0000.162] I> Boot-device: eMMC [0000.165] I> Boot-device: eMMC [0000.175] I> Sdmmc: HS400 mode enabled [0000.179] I> ECC region[0]: Start:0x0, End:0x0 [0000.183] I> ECC region[1]: Start:0x0, End:0x0 [0000.187] I> ECC region[2]: Start:0x0, End:0x0 [0000.191] I> ECC region[3]: Start:0x0, End:0x0 [0000.196] I> ECC region[4]: Start:0x0, End:0x0 [0000.200] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0000.205] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.210] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.214] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.219] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.224] E> FAILED: Thermal config [0000.232] E> FAILED: MEMIO rail config [0000.250] I> Boot-device: eMMC [0000.259] I> sdmmc bdev is already initialized [0000.332] I> MB1 done ����main enter SPE VERSION #: R01.00.14 Created: Sep 19 2018 @ 11:03:21 HW Function test Start Scheduler. in late init �� [0000.341] I> Welcome to MB2(TBoot-BPMP) (version: 00.00.2018.32-mobile-938a8cd8) [0000.342] I> DMA Heap @ [0x526fa000 - 0x52ffa000] [0000.342] I> Default Heap @ [0xd486400 - 0xd48a400] [0000.343] E> DEVICE_PROD: Invalid value data = 70020000, size = 0. [0000.349] W> device prod register failed [0000.353] I> Boot-device: eMMC [0000.355] I> Boot_device: SDMMC_BOOT instance: 3 [0000.361] I> sdmmc-3 params source = boot args [0000.364] I> sdmmc bdev is already initialized [0000.368] I> sdmmc-3 params source = boot args [0000.377] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0000.383] I> Found 42 partitions in SDMMC_USER (instance 3) [0000.384] W> No valid slot number is found in scratch register [0000.389] W> Return default slot: _a [0000.393] I> Active Boot chain : 0 [0000.396] I> parsing oem signed section of bpmp-fw header done [0000.402] I> bpmp-fw binary init read from storage [0000.407] I> oem authentication of bpmp-fw header done [0000.413] I> bpmp-fw binary done read from storage [0000.416] I> bpmp-fw: Authentication init Done [0000.421] I> parsing oem signed section of cpubl header done [0000.426] I> cpubl binary init read from storage [0000.430] I> bpmp-fw: Authentication Finalize Done [0000.435] I> oem authentication of cpubl header done [0000.440] I> cpubl binary done read from storage [0000.444] I> cpubl: Authentication init Done [0000.449] I> parsing oem signed section of rce header done [0000.454] I> rce binary init read from storage [0000.458] I> Relocating BR-BCT [0000.461] I> cpubl: Authentication Finalize Done [0000.466] I> oem authentication of rce header done [0000.470] I> rce binary done read from storage [0000.474] I> rce: Authentication init Done [0000.479] I> parsing oem signed section of ape header done [0000.483] I> ape binary init read from storage [0000.488] I> rce: Authentication Finalize Done [0000.492] I> oem authentication of ape header done [0000.497] I> ape binary done read from storage [0000.501] I> ape: Authentication init Done [0000.506] I> parsing oem signed section of tos header done [0000.510] I> tos binary init read from storage [0000.515] I> ape: Authentication Finalize Done [0000.519] I> oem authentication of tos header done [0000.523] I> tos binary done read from storage [0000.528] I> tos: Authentication init Done [0000.532] I> parsing oem signed section of bpmp-fw-dtb header done [0000.538] I> bpmp-fw-dtb binary init read from storage [0000.543] I> tos: Authentication Finalize Done [0000.549] I> oem authentication of bpmp-fw-dtb header done [0000.555] I> bpmp-fw-dtb binary done read from storage [0000.557] I> bpmp-fw-dtb: Authentication init Done [0000.562] I> parsing oem signed section of cpubl-dtb header done [0000.568] I> cpubl-dtb binary init read from storage [0000.573] I> bpmp-fw-dtb: Authentication Finalize Done [0000.611] I> oem authentication of cpubl-dtb header done [0000.611] I> cpubl-dtb binary done read from storage [0000.612] I> cpubl-dtb: Authentication init Done [0000.614] I> parsing oem signed section of eks header done [0000.614] I> eks binary init read from storage [0000.615] I> cpubl-dtb: Authentication Finalize Done [0000.616] I> oem authentication of eks header done [0000.619] I> eks binary done read from storage [0000.624] I> eks: Authentication init Done [0000.628] I> eks: Authentication Finalize Done [0000.632] I> EKB detected (length: 0x410) @ VA:0x52700400 ��NOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:15:32, Jul 26 2021 ipc-unittest-main: 1519: Welcome to IPC unittest!!! ipc-unittest-main: 1531: waiting forever ipc-unittest-srv: 329: Init unittest services!!! hwkey-agent: 41: hwkey-agent is running!! hwkey-agent: 315: key_mgnt_processing ....... hwkey-agent: 223: Setting EKB key 0 to slot 14 hwkey-agent: 178: Init hweky-agent services!! luks-srv: 40: luks-srv is running!! luks-srv: 157: Init luks-srv IPC services!! platform_bootstrap_epilog: trusty bootstrap complete �� welcome to lk calling constructors initializing heap creating bootstrap completion thread top of bootstrap2() initializing platform bpmp: platform_init tag is e73a758761f0c6d24a1e69a2ac6b5035 tag_show initialized dt initialized mail initialized chipid initialized fuse initialized sku initialized speedo initialized ec_get_ec_list: found 45 ecs ec initialized ec_mrq initialized vmon_populate_monitors: found 3 monitors vmon initialized adc initialized fmon_populate_monitors: found 73 monitors fmon initialized fmon_mrq initialized reset initialized nvhs initialized 392 clocks registered WARNING: pll_c4 has no dyn ramp clk_mrq_init: mrq handler registered clk initialized nvlink initialized io_dpd initialized io_dpd initialized thermal initialized i2c5 controller initialized initialized i2c mrq handling i2c initialized regulator initialized avfs_clk_platform initialized soctherm initialized aotag initialized powergate initialized dvs initialized pm initialized pg_late initialized strap initialized tag initialized emc initialized clk_dt initialized avfs_ccplex_platform initialized tj_max: dt node not found tj_init initialized uphy_mrq_init: mrq handler registered uphy_dt initialized uphy initialized safereg_init: period 80 ms ec_late initialized mrq initialized �� [0001.135] I> Welcome to Cboot ��fmon_post initialized ��[0001.135] I> Cboot Version: t194-cfa2bc91 [0001.135] I> CPU-BL Params @ 0xf2820000 [0001.136] I> 0) Base:0x00000000 Size:0x00000000 [0001.139] I> 1) Base:0xf1100000 Size:0x00100000 [0001.144] I> 2) Base:0xf2000000 Size:0x00200000 [0001.148] I> 3) Base:0xf1200000 Size:0x00200000 ��clk_set_parent failed for clk i2c2, parent pll_aon (-22) clk_set_parent failed for clk i2c8, parent pll_aon (-22) clk_dt_late initialized machine_check initialized pm_post initialized dbells initialized avfs_clk_platform_post initialized dmce initialized cvc initialized ccplex_avfs_hw_init: nafll_cluster0: not monitored ccplex_avfs_hw_init: nafll_cluster1: not monitored ccplex_avfs_hw_init: nafll_cluster2: not monitored ccplex_avfs_hw_init: nafll_cluster3: not monitored avfs_clk_mach_post initialized regulator_post initialized rm initialized sc7_diag initialized thermal_test initialized serial_late initialized clk_post initialized clk_dt_post initialized mc_reg initialized pg_post initialized dyn_modules initialized sku_debugfs initialized speedo_debugfs initialized adc_debugfs initialized clk_debugfs initialized ��[0001.153] I> 4) Base:0xf1000000 Size:0x00100000 [0001.232] I> 5) Base:0xf0f00000 Size:0x00100000 [0001.237] I> 6) Base:0xf3800000 Size:0x00400000 [0001.241] I> 7) Base:0xf1c00000 Size:0x00400000 [0001.245] I> 8) Base:0xf0e00000 Size:0x00100000 [0001.250] I> 9) Base:0xf0d00000 Size:0x00100000 [0001.254] I> 10) Base:0xf3000000 Size:0x00800000 [0001.259] I> 11) Base:0x40000000 Size:0x00040000 [0001.263] I> 12) Base:0xf0c00000 Size:0x00100000 [0001.268] I> 13) Base:0x40046000 Size:0x00002000 [0001.272] I> 14) Base:0x40048000 Size:0x00002000 ��emc_debugfs initialized dvs_debugfs initialized ��[0001.277] I> 15) Base:0xac000000 Size:0x00004000 ��fmon_debugfs initialized vmon_debugfs initialized pg_debugfs initialized profile_fs initialized debugfs_cons initialized mail_fs initialized profile initialized cvc_debugfs initialized dmce_debugfs initialized ec_debugfs initialized rm_debugfs initialized soctherm_debug initialized gr_reader initialized mods initialized dt_fs initialized debugfs_mrq initialized debug_mrq initialized debug_safereg initialized initializing target calling apps_init() starting app shell entering main console loop ] ��[0001.286] I> 16) Base:0x4004a000 Size:0x00002000 [0001.336] I> 17) Base:0xf0b00000 Size:0x00100000 [0001.341] I> 18) Base:0x4004c000 Size:0x00002000 [0001.345] I> 19) Base:0xf2200000 Size:0x00600000 [0001.350] I> 20) Base:0x4004e000 Size:0x00002000 [0001.354] I> 21) Base:0xf0ad0000 Size:0x0000c000 [0001.359] I> 22) Base:0x00000000 Size:0x00000000 [0001.363] I> 23) Base:0xf0ae0000 Size:0x00020000 [0001.368] I> 24) Base:0xf6000000 Size:0x02000000 [0001.372] I> 25) Base:0x40050000 Size:0x00002000 [0001.377] I> 26) Base:0x40040000 Size:0x00006000 [0001.381] I> 27) Base:0xf1800000 Size:0x00400000 [0001.385] I> 28) Base:0xf4c00000 Size:0x01400000 [0001.390] I> 29) Base:0xf1400000 Size:0x00400000 [0001.394] I> 30) Base:0x00000000 Size:0x00000000 [0001.399] I> 31) Base:0x00000000 Size:0x00000000 [0001.403] I> 32) Base:0xf8000000 Size:0x08000000 [0001.408] I> 33) Base:0x00000000 Size:0x00000000 [0001.412] I> 34) Base:0xf3c00000 Size:0x01000000 [0001.417] I> 35) Base:0xab000000 Size:0x01000000 [0001.421] I> 36) Base:0xa0000000 Size:0x0b000000 [0001.426] I> 37) Base:0xf2800000 Size:0x00800000 [0001.430] I> 38) Base:0x80000000 Size:0x20000000 [0001.435] I> 39) Base:0xb0000000 Size:0x08000000 [0001.439] I> 40) Base:0x00000000 Size:0x00000000 [0001.443] I> 41) Base:0x00000000 Size:0x00000000 [0001.448] I> 42) Base:0x00000000 Size:0x00000000 [0001.452] I> 43) Base:0x00000000 Size:0x00000000 [0001.457] I> 44) Base:0x00000000 Size:0x00000000 [0001.461] I> 45) Base:0x00000000 Size:0x00000000 [0001.466] GIC-SPI Target CPU: 0 [0001.469] Interrupts Init done [0001.472] calling constructors [0001.475] initializing heap [0001.477] I> Heap: [0xa0699b80 ... 0xab000000] [0001.481] initializing threads [0001.484] initializing timers [0001.487] creating bootstrap completion thread [0001.491] top of bootstrap2() [0001.494] CPU: MIDR: 0x4E0F0040, MPIDR: 0x80000000 [0001.499] initializing platform [0001.502] E> DEVICE_PROD: Invalid value data = 0, size = 0. [0001.507] W> device prod register failed [0001.511] I> Bl_dtb @0xaaf00000 [0001.517] W> "plugin-manager" doesn't exist, creating [0001.519] W> "ids" doesn't exist, creating [0001.523] W> "connection" doesn't exist, creating [0001.527] W> "configs" doesn't exist, creating [0001.539] E> failed to read label property for node 227172: 13 [0001.542] E> failed to read reg property for node 227260: 13 [0001.545] E> failed to read label property for node 227312: 13 [0001.550] E> failed to read label property for node 227380: 13 [0001.555] E> failed to read label property for node 227416: 13 [0001.561] E> failed to read label property for node 227452: 13 [0001.567] E> failed to read reg property for node 227520: 13 [0001.572] E> failed to read label property for node 227572: 13 [0001.579] I> Find /i2c@3160000's alias i2c0 [0001.581] I> Reading eeprom i2c=0 address=0x50 [0001.610] I> Device at /i2c@3160000:0x50 [0001.611] I> Reading eeprom i2c=0 address=0x56 [0001.635] I> Device at /i2c@3160000:0x56 [0001.637] I> Find /i2c@3180000's alias i2c2 [0001.637] I> Reading eeprom i2c=2 address=0x54 [0001.639] E> I2C: slave not found in slaves. [0001.639] E> I2C: Could not write 0 bytes to slave: 0x00a8 with repeat start true. [0001.640] E> I2C_DEV: Failed to send register address 0x00000000. [0001.640] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa8 at 0x00000000 via instance 2. [0001.649] E> eeprom: Failed to read I2C slave device [0001.654] I> Eeprom read failed 0x3526070d [0001.658] I> Reading eeprom i2c=2 address=0x57 [0001.662] E> I2C: slave not found in slaves. [0001.666] E> I2C: Could not write 0 bytes to slave: 0x00ae with repeat start true. [0001.674] E> I2C_DEV: Failed to send register address 0x00000000. [0001.680] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xae at 0x00000000 via instance 2. [0001.689] E> eeprom: Failed to read I2C slave device [0001.694] I> Eeprom read failed 0x3526070d [0001.698] I> Reading eeprom i2c=2 address=0x52 [0001.702] E> I2C: slave not found in slaves. [0001.706] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.714] E> I2C_DEV: Failed to send register address 0x00000000. [0001.720] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 2. [0001.729] E> eeprom: Failed to read I2C slave device [0001.734] I> Eeprom read failed 0x3526070d [0001.739] I> Find /i2c@c240000's alias i2c1 [0001.742] I> Reading eeprom i2c=1 address=0x52 [0001.748] E> I2C: slave not found in slaves. [0001.751] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.758] E> I2C_DEV: Failed to send register address 0x00000000. [0001.764] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.773] E> eeprom: Retry to read I2C slave device. [0001.778] E> I2C: slave not found in slaves. [0001.782] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.790] E> I2C_DEV: Failed to send register address 0x00000000. [0001.796] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.805] E> eeprom: Failed to read I2C slave device [0001.810] I> Eeprom read failed 0x3526070d [0001.814] I> Reading eeprom i2c=1 address=0x50 [0001.818] E> I2C: slave not found in slaves. [0001.822] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.830] E> I2C_DEV: Failed to send register address 0x00000000. [0001.836] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0001.845] E> eeprom: Retry to read I2C slave device. [0001.850] E> I2C: slave not found in slaves. [0001.854] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.862] E> I2C_DEV: Failed to send register address 0x00000000. [0001.868] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0001.877] E> eeprom: Failed to read I2C slave device [0001.882] I> Eeprom read failed 0x3526070d [0001.886] I> create_pm_ids: id: 2888-0004-400-K, len: 15 [0001.891] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.902] I> create_pm_ids: id: 2822-0000-700-J, len: 15 [0001.907] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.918] I> Adding plugin-manager/ids/2888-0004-400=/i2c@3160000:module@0x50 [0001.926] W> "i2c@3160000" doesn't exist, creating [0001.930] W> "module@0x50" doesn't exist, creating [0001.935] I> Adding plugin-manager/ids/2822-0000-700=/i2c@3160000:module@0x56 [0001.942] W> "module@0x56" doesn't exist, creating [0001.948] I> Adding plugin-manager/cvm [0001.950] W> "chip-id" doesn't exist, creating [0001.954] I> Adding plugin-manager/chip-id/A02P [0001.959] I> Plugin-manager override starting [0001.964] I> node /plugin-manager/fragement-tegra-wdt-en matches [0001.971] I> node /plugin-manager/fragement-soft-wdt matches [0001.979] I> node /plugin-manager/fragment-pcie-c5-rp matches [0001.983] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches [0001.994] I> Disable plugin-manager status in FDT [0001.995] I> Plugin-manager override finished successfully [0001.996] I> gpio framework initialized [0002.001] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' driver [0002.008] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon' driver [0002.014] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x46 [0002.022] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0002.030] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0002.036] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.042] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x44 [0002.050] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0002.057] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0002.064] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.072] I> fixed regulator driver initialized [0002.083] I> register 'maxim' power off handle [0002.084] I> virtual i2c enabled [0002.084] I> registered 'maxim,max20024' pmic [0002.086] I> tegrabl_gpio_driver_register: register 'max20024-gpio' driver [0002.093] I> Boot-device: eMMC [0002.096] I> Boot_device: SDMMC_BOOT instance: 3 [0002.104] I> sdmmc-3 params source = boot args [0002.105] I> create_pm_ids: id: 2888-0004-400-K, len: 15 [0002.110] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.121] I> create_pm_ids: id: 2822-0000-700-J, len: 15 [0002.126] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.137] I> sdmmc bdev is already initialized [0002.141] I> sdmmc-3 params source = boot args [0002.172] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0002.184] I> Found 42 partitions in SDMMC_USER (instance 3) [0002.194] I> enabling 'vdd-hdmi-5v0' regulator [0002.200] I> regulator 'vdd-hdmi-5v0' already enabled [0002.200] I> hdmi cable connected [0002.202] W> set volts not configured for 'vdd-1v0' [0002.204] W> set volts not configured for 'vdd-1v8-hs' [0002.205] I> retrieved tmds range from prod_list_hdmi_soc [0002.209] E> invalid display type [0002.213] E> invalid display type [0002.215] E> cannot find any other nvdisp nodes [0002.230] I> edid read success [0002.242] I> edid read success [0002.243] I> width = 640, height = 480, frequency = 25174825 [0002.243] I> width = 640, height = 480, frequency = 25174825 [0002.243] I> width = 1920, height = 1200, frequency = 154000000 [0002.244] I> width = 1920, height = 1080, frequency = 148500000 [0002.244] I> width = 1920, height = 1080, frequency = 148351648 [0002.249] I> width = 1280, height = 720, frequency = 74175824 [0002.254] I> width = 720, height = 480, frequency = 26973026 [0002.260] I> width = 720, height = 480, frequency = 26973026 [0002.265] I> width = 640, height = 480, frequency = 25174825 [0002.271] I> width = 1920, height = 1080, frequency = 148351648 [0002.276] I> width = 720, height = 576, frequency = 26973026 [0002.282] I> width = 1280, height = 720, frequency = 74175824 [0002.288] I> width = 1920, height = 1080, frequency = 74175824 [0002.293] I> width = 1920, height = 1080, frequency = 74175824 [0002.299] I> width = 1920, height = 1080, frequency = 74175824 [0002.305] I> Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.315] I> hdmi_enable, starting HDMI initialisation [0002.320] I> hdmi_enable, HDMI initialisation complete [0002.330] I> Load in CBoot Boot Options partition and parse it [0002.336] E> Error -9 when finding node with path /boot-configuration [0002.337] E> tegrabl_cbo_parse_info: "boot-configuration" not found in CBO file. [0002.340] I> Using default boot order [0002.344] I> boot-dev-order :- [0002.346] I> 1.sd [0002.348] I> 2.usb [0002.350] I> 3.nvme [0002.352] I> 4.emmc [0002.354] I> 5.net [0002.356] I> Hit any key to stop autoboot: 4 3 2 1 [0004.363] initializing target [0004.363] calling apps_init() [0004.364] starting app kernel_boot_app [0004.383] I> found decompressor handler: lz4-legacy [0004.384] I> decompressing BMP blob ... [0004.394] I> Kernel type = Normal [0004.395] I> ########## SD (0) boot ########## [0004.395] I> No sdcard [0004.396] I> -0 params source = [0004.396] E> Blockdev open: exit error [0004.396] E> SD boot failed, err: 724238353 [0004.396] I> ########## USB (0) boot ########## [0004.401] W> No valid slot number is found in scratch register [0004.402] W> Return default slot: _a [0004.409] I> Validate XUSB-FW ... [0004.409] I> T19x: Authenticate XUSB-FW (bin_type: 11), max size 0x28000 [0004.414] I> Encryption fuse is not ON [0004.416] I> USB Firmware Version: 60.09 release [0004.476] I> regulator of usb2-0 already enabled [0004.483] I> regulator of usb2-1 already enabled [0004.490] I> regulator of usb2-2 already enabled [0004.499] I> enabling 'vdd-5v-sata' regulator [0005.567] I> USB 2.0 port 1 new high-speed USB device detected [0005.569] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa4ad2000, cmd_ring.dma = 0xa4ad20c0 [0005.670] I> Start to enumerate device [0005.671] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa4ad2000, cmd_ring.dma = 0xa4ad20c0 [0005.676] I> [0005.676] I> Enumerated USB Device 1a40:0101 [0005.676] I> [0005.677] I> Hub: [0005.678] I> Downstream ports : 4 [0005.678] I> Power switching : Ganged [0005.678] I> Compound device : No [0005.678] I> Over-current protection : Global [0005.683] I> Hub avg delay : 4 ns [0005.687] I> Enable hub ports [0005.901] I> Device detected on port 3 [0006.714] I> Reset port 3 [0006.769] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa4ad2000, cmd_ring.dma = 0xa4ad20c0 [0006.870] I> Start to enumerate device [0006.871] W> handle_command_completion_event: WARNING: Command was not successfully completed (0x04) [0009.880] W> xusbh_wait_irq: Timed out! status = 0x00 [0012.889] W> xusbh_wait_irq: Timed out! status = 0x00 [0012.890] E> Failed to enumerate USB device [0012.890] E> failed to start xhci controller [0012.890] E> Error in init of XUSB host driver, err: 7979000c [0012.891] W> Failed to initialize device 5-0 [0012.891] E> USB boot failed, err: 2037973004 [0012.891] I> ########## NVME (0) boot ########## [0012.895] I> Initializing nvme device instance 0 [0012.900] I> Initializing nvme controller [0012.904] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14180000 [0012.910] I> vpcie3v3-supply not found [0012.914] I> vpcie12v-supply not found [0012.917] W> Failed to get nvidia,plat-gpios [0012.921] I> tegrabl_pcie_soc_preinit: (0): [0012.926] I> Unpowergate [0012.928] I> tegrabl_car_clk_disable(0) ... [0012.932] I> tegrabl_car_rst_set(CORE, 0) ... [0012.936] I> tegrabl_car_rst_set(APB, 0) ... [0012.940] I> tegrabl_car_clk_enable(0) ... [0012.944] I> tegrabl_car_rst_clear(APB, 0) ... [0012.949] I> tegrabl_set_ctrl_state(0) [0012.952] I> CLR PCIE_APB:6 [0012.955] I> tegrabl_pcie_soc_init: (0): [0012.958] I> APPL initialization ... [0012.962] I> poweron phys [0012.964] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14180000 [0012.971] I> tegrabl_power_on_phy: power on phy @0x3e30000 [0012.976] I> tegrabl_power_on_phy: power on phy @0x3e40000 [0012.981] I> tegrabl_power_on_phy: power on phy @0x3e50000 [0012.987] I> tegrabl_power_on_phy: power on phy @0x3e60000 [0013.119] I> PCIe controller-0 link is up [0013.120] I> tegra_pcie_info[0].cfg0_base = 0x38000000 [0013.120] I> tegra_pcie_info[0].cfg1_base = 0x38020000 [0013.120] I> tegra_pcie_info[0].atu_dma_base = 0x38040000 [0013.121] I> tegra_pcie_bus[0].mem = 0x38200000 [0013.121] I> Scanning busnr: 0 devfn: 0 [0013.121] I> PCIe IDs: 0x1ad010de [0013.124] I> PCIe RID_CC: 0x60400a1 [0013.128] I> Scanning busnr: 1 devfn: 0 [0013.131] I> PCIe IDs: 0xa808144d [0013.135] I> PCIe RID_CC: 0x1080200 [0013.138] I> PCI Config: I/O=0x38100000, Memory=0x38200000 [0013.143] I> MEM64 bar_num=0 bar=0x38200000 [0013.147] I> Number of PCIe devices detected: 2 [0013.152] I> NVME page size: 4096 [0013.156] I> NVMe serial number: S4EVNX0T122150B [0013.160] I> NVMe model number: Samsung SSD 970 EVO Plus 500GB [0013.166] I> NVMe firmware revision: 2B2QEXM7 [0013.171] I> block_count: 976773168 [0013.174] I> supported_lba: 0 [0013.177] I> block_size_log2: 0x9 [0013.180] I> tegrabl_create_io_queue_cmd: queue size: 2 [0013.185] I> tegrabl_create_io_queue_cmd: queue size: 2 [0013.190] I> nvme device id 000a0000 [0013.193] I> nvme-0 params source = [0013.197] I> Found 11 partitions in NVME (instance 0) [0013.202] I> Look for boot partition [0013.205] I> Fallback: assuming 0th partition is boot partition [0013.217] I> Detect filesystem [0013.219] I> Loading kernel-bootctrl from partition [0013.219] I> Loading partition kernel-bootctrl at 0xa4bb0000 from device(0xa) [0013.227] W> tegrabl_get_kernel_bootctrl: magic number(0x00000000) is invalid [0013.232] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data [0013.239] I> Loading extlinux.conf ... [0013.243] I> Loading extlinux.conf binary from rootfs ... [0013.248] I> rootfs path: /nvme/boot/extlinux/extlinux.conf [0013.255] I> Loading extlinux.conf sig file from rootfs ... [0013.259] I> rootfs path: /nvme/boot/extlinux/extlinux.conf.sig [0013.265] I> Validate extlinux.conf ... [0013.269] I> T19x: Authenticate extlinux.conf (bin_type: 54), max size 0x2000 [0013.276] I> Encryption fuse is not ON [0013.279] I> L4T boot options [0013.282] I> [1]: "primary kernel" [0013.285] I> Enter choice: [0016.289] I> Continuing with default option: 1 [0016.289] I> Loading kernel ... [0016.289] I> Loading kernel binary from rootfs ... [0016.289] I> rootfs path: /nvme/boot/Image [0016.463] I> Loading kernel sig file from rootfs ... [0016.463] I> rootfs path: /nvme/boot/Image.sig [0016.464] I> overload load_size to 34484232 (from 34549768) [0016.464] I> Validate kernel ... [0016.465] I> T19x: Authenticate kernel (bin_type: 37), max size 0x5000000 [0016.779] E> digest on binary did not match!! [0016.779] C> OEM authentication of kernel payload failed! [0016.779] W> Failed to validate kernel binary from rootfs (err=1077936152, fail=0) [0016.780] W> Security fuse not burned, ignore validation failure [0016.780] I> restore load_size to 34549768 [0016.797] I> Loading kernel-dtb ... [0016.798] I> No kernel-dtb binary path [0016.798] I> Continue to load from partition ... [0016.798] W> No valid slot number is found in scratch register [0016.799] W> Return default slot: _a [0016.801] I> A/B: bin_type (38) slot 0 [0016.804] I> Loading kernel-dtb from partition [0016.809] I> Loading partition kernel-dtb at 0x91000000 from device(0xa) [0016.820] I> Validate kernel-dtb ... [0016.820] I> T19x: Authenticate kernel-dtb (bin_type: 38), max size 0x400000 [0016.828] I> Encryption fuse is not ON [0016.831] I> Loading ramdisk from rootfs ... [0016.833] I> Loading ramdisk binary from rootfs ... [0016.838] I> rootfs path: /nvme/boot/initrd [0016.878] I> Loading ramdisk sig file from rootfs ... [0016.879] I> rootfs path: /nvme/boot/initrd.sig [0016.880] I> overload load_size to 7238344 (from 7238352) [0016.880] I> Validate ramdisk ... [0016.880] I> T19x: Authenticate ramdisk (bin_type: 54), max size 0x4000000 [0016.947] I> Encryption fuse is not ON [0016.963] I> removable_boot_load_kernel_and_dtb: force NVME bdev to close !!! [0016.963] I> Kernel hdr @0xa4bb0000 [0016.964] I> Kernel dtb @0x90000000 [0016.964] I> decompressor handler not found [0016.964] I> Copying kernel image (34549768 bytes) from 0xa4bb0000 to 0x80080000 ... [0016.974] I> Done [0016.975] I> Updated bpmp info to DTB [0016.976] I> Ramdisk: Base: 0x92000000; Size: 0x6e72c8 [0016.977] I> Updated initrd info to DTB [0016.977] W> WARN: Fail to override "console=none" in commandline [0016.983] I> Active rootfs suffix: [0016.986] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0016.993] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0017.001] W> No valid slot number is found in scratch register [0017.006] W> Return default slot: _a [0017.010] I> Active slot suffix: [0017.013] I> add_boot_slot_suffix: slot_suffix = [0017.018] I> Linux Cmdline: console=ttyTCU0,115200 video=tegrafb earlycon=tegra_comb_uart,mmio32,0x0c168000 gpt rootfs.slot_suffix= tegra_fbmem=0x800000@0xa06aa000 lut_mem=0x2008@0xa06a5000 usbcore.old_scheme_first=1 tegraid=19.1.2.0.0 maxcpus=8 boot.slot_suffix= boot.ratchetvalues=0.4.2 vpr_resize sdhci_tegra.en_boot_part_access=1 [0017.047] I> Updated bootarg info to DTB [0017.051] W> MAC addr invalid! [0017.054] E> Failed to get WIFI MAC address [0017.058] W> MAC addr invalid! [0017.061] E> Failed to get Bluetooth MAC address [0017.065] I> eeprom_get_mac_addr: MAC (type: 2): 00:04:4b:e5:92:60 [0017.072] W> "plugin-manager" doesn't exist, creating [0017.076] I> Adding /chosen/plugin-manager/cvm [0017.080] W> "chip-id" doesn't exist, creating [0017.085] I> Adding /chosen/plugin-manager/chip-id [0017.089] W> "configs" doesn't exist, creating [0017.093] I> Adding /chosen/plugin-manager/configs [0017.098] W> "ids" doesn't exist, creating [0017.102] I> Adding /chosen/plugin-manager/ids [0017.107] W> "odm-data" doesn't exist, creating [0017.111] I> Adding /chosen/plugin-manager/odm-data [0017.118] W> "memory" doesn't exist, creating [0017.120] I> [0] START: 0x80000000, END: 0xac000000 [0017.124] I> [1] START: 0xac004000, END: 0xf0ad0000 [0017.129] I> [2] START: 0xf0adc000, END: 0xf0ae0000 [0017.134] I> dram_block larger than 80000000 [0017.138] I> [3] START: 0x100000000, END: 0x880000000 [0017.143] I> added [base:0x80000000, size:0x2c000000] to /memory [0017.149] I> added [base:0xac200000, size:0x44800000] to /memory [0017.154] I> added [base:0x100000000, size:0x780000000] to /memory [0017.161] I> Updated memory info to DTB [0017.164] E> add_disp_param: failed to get display params for du=1 [0017.171] W> "reset" doesn't exist, creating [0017.175] I> Adding ecid(00000001645df740140000000c0100c0) to DT [0017.180] I> NVG: Logical CPU: 0; MPIDR: 0x80000000 [0017.185] I> NVG: Logical CPU: 1; MPIDR: 0x80000001 [0017.190] I> NVG: Logical CPU: 2; MPIDR: 0x80000100 [0017.194] I> NVG: Logical CPU: 3; MPIDR: 0x80000101 [0017.199] I> NVG: Logical CPU: 4; MPIDR: 0x80000200 [0017.204] I> NVG: Logical CPU: 5; MPIDR: 0x80000201 [0017.209] I> NVG: Logical CPU: 6; MPIDR: 0x80000300 [0017.213] I> NVG: Logical CPU: 7; MPIDR: 0x80000301 [0017.219] W> "misc-data" doesn't exist, creating [0017.223] I> Boot-device: eMMC [0017.225] I> Add boot-sdmmc to plugin-manager/misc-data [0017.231] I> Add storage-sdmmc to plugin-manager/misc-data [0017.236] W> Unknown storage device [0017.240] I> Add serial number:1421220028681 as DT property [0017.246] I> Plugin-manager override starting [0017.249] I> node /plugin-manager/fragement-tegra-wdt-en matches [0017.257] I> node /plugin-manager/fragement-soft-wdt matches [0017.264] I> node /plugin-manager/fragment-pcie-c5-rp matches [0017.268] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches [0017.279] I> Disable plugin-manager status in FDT [0017.279] I> Plugin-manager override finished successfully [0017.282] I> tegrabl_load_kernel_and_dtb: Done [0017.305] I> Kernel EP: 0x80080000, DTB: 0x90000000 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.253-g36e08c2 (krishnakumar@krishnakumar-PC) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Tue Nov 9 13:22:27 IST 2021 [ 0.000000] Boot CPU: AArch64 Processor [4e0f0040] [ 0.000000] OF: fdt:memory scan node memory, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 2c000000 [ 0.000000] OF: fdt: - ac200000 , 44800000 [ 0.000000] OF: fdt: - 100000000 , 780000000 [ 0.000000] earlycon: tegra_comb_uart0 at MMIO32 0x000000000c168000 (options '') [ 0.000000] bootconsole [tegra_comb_uart0] enabled [ 0.000000] Found tegra_fbmem: 00800000@a06aa000 [ 0.000000] Found lut_mem: 00002008@a06a5000 ��WARNING: pll_d3 has no dyn ramp ��[ 5.507573] cgroup: cgroup2: unknown option "nsdelegate" [ 6.615051] using random self ethernet address [ 6.615217] using random host ethernet address [ 6.640891] iwlwifi 0003:01:00.0: Direct firmware load for iwlwifi-8265-26.ucode failed with error -2 [ 6.641194] iwlwifi 0003:01:00.0: Falling back to user helper [ 6.678873] random: crng init done [ 6.679021] random: 7 urandom warning(s) missed due to ratelimiting [ 6.721814] imx290: loading out-of-tree module taints kernel. [ 7.174727] using random self ethernet address [ 7.174897] using random host ethernet address [ 7.335713] eimx290 30-0042: cam_init 1672MCU CMD ID CAM INIT Success !! [ 7.954072] eimx290 32-0042: cam_init 1672MCU CMD ID CAM INIT Success !! [ 8.080602] Bridge firewalling registered [ 8.097902] iwlwifi 0003:01:00.0: Direct firmware load for iwlwifi-8265-25.ucode failed with error -2 [ 8.097905] iwlwifi 0003:01:00.0: Falling back to user helper [ 8.285290] iwlwifi 0003:01:00.0: Direct firmware load for iwlwifi-8265-24.ucode failed with error -2 [ 8.285294] iwlwifi 0003:01:00.0: Falling back to user helper [ 8.289730] iwlwifi 0003:01:00.0: Direct firmware load for iwlwifi-8265-23.ucode failed with error -2 [ 8.289733] iwlwifi 0003:01:00.0: Falling back to user helper [ 8.493267] thermal thermal_zone8: failed to read out thermal zone (-5) [ 8.978287] eimx290 34-0042: cam_init 1672MCU CMD ID CAM INIT Success !! [ 9.562074] eimx290 35-0042: cam_init 1672MCU CMD ID CAM INIT Success !! Ubuntu 18.04.5 LTS nkb-desktop ttyTCU0