[09:18:48.814]收←◆\0
[09:22:18.062]收←◆\0
[09:22:18.279]收←◆?
[0203.241] I> MB1 (version: 1.2.0.0-t234-54845784-562369e5)
[0203.246] I> t234-A01-0-Silicon (0x12347) Prod
[0203.251] I> Boot-mode : BPMP Diagnostic
[0203.254] I> Entry timestamp: 0x00000000
[0203.258] I> last_boot_error: 0x0
[0203.261] I> BR-BCT: preprod_dev_sign: 0
[0203.265] I> rst_source: 0x0, rst_level: 0x0
[0203.269] I> Task: Initialize MB2 params
[0203.274] I> MB2-params @ 0x40060000
[0203.277] I> Task: Crypto init
[0203.280] I> Task: Perform MB1 KAT tests
[0203.284] I> Task: NVRNG health check
[0203.287] I> NVRNG: Health check success
[0203.291] I> Task: Secure debug controls
[0203.295] I> Task: strap war set
[0203.298] I> Task: Program NV master stream id
[0203.302] I> Task: Verify boot mode
[0203.308] I> Task: Alias fuses
[0203.311] W> FUSE_ALIAS: Fuse alias on production fused part is not supported.
[0203.318] I> Task: Print SKU type
[0203.321] I> FUSE_OPT_CCPLEX_CLUSTER_DISABLE = 0x000001c0
[0203.327] I> FUSE_OPT_GPC_DISABLE = 0x00000000
[0203.331] I> FUSE_OPT_TPC_DISABLE = 0x00000001
[0203.335] I> FUSE_OPT_DLA_DISABLE = 0x00000000
[0203.340] I> FUSE_OPT_PVA_DISABLE = 0x00000000
[0203.344] I> FUSE_OPT_NVENC_DISABLE = 0x00000000
[0203.348] I> FUSE_OPT_NVDEC_DISABLE = 0x00000000
[0203.353] I> FUSE_OPT_FSI_DISABLE = 0x00000000
[0203.357] I> FUSE_OPT_EMC_DISABLE = 0x00000000
[0203.361] I> FUSE_BOOTROM_PATCH_VERSION = 0x7
[0203.365] I> FUSE_PSCROM_PATCH_VERSION = 0x7
[0203.370] I> FUSE_OPT_ADC_CAL_F
[09:22:18.308]收←◆USE_REV = 0x2
[0203.374] I> FUSE_SKU_INFO_0 = 0xd2
[0203.377] I> FUSE_OPT_SAMPLE_TYPE_0 = 0x3 PS 
[0203.381] I> FUSE_PACKAGE_INFO_0 = 0x2
[0203.385] I> SKU: Prod
[0203.387] I> Task: Boost clocks
[0203.390] I> Initializing PLLC2 for AXI_CBB.
[0203.394] I> AXI_CBB : src = 35, divisor = 0
[0203.398] I> Task: Voltage monitor
[0203.402] I> VMON: Vmon re-calibration and fine tuning done
[0203.407] I> Task: UPHY init
[0203.410] W> UPHY: UPHY lane info table is empty in MB1 BCT.
[0203.416] I> Task: Boot device init
[0203.419] I> Boot_device: RCM
[0203.422] I> USB configuration success
[0203.426] I> Task: TSC init
[0203.429] I> Task: Enable WDT 5th expiry
[0203.432] I> Task: I2C register
[0203.435] I> Task: Set I2C bus freq
[0203.439] I> Task: Reset FSI
[0203.441] I> Task: Enable clock-mon
[0203.456] I>
[09:22:18.512]收←◆ FMON: Fmon re-programming done
[0203.460] I> Task: Mapper init
[0203.463] I> Task: MB1 fixed firewalls
[0203.469] W> Firewall readback mismatch
[0203.474] I> Task: Load MB2/Applet/FSKP
[0203.478] I> Loading MB2 Applet
[0203.481] I> Slot: 0
[0203.483] I> Binary[21] block-352321536 (partition size: 0x50000)
[0203.489] I> Binary name: MB2-Applet
[0203.492] I> Size of crypto header is 8192
[0203.496] I> Size of crypto header is 8192
[0203.500] I> BCH of MB2-Applet read from storage
[0203.505] I> BCH address is : 0x4004e000
[0203.509] I> MB2-Applet header integrity check is success
[0203.514] I> Binary magic in BCH component 0 is MB2A
[0203.519] I> component binary type is 21
[0203.523] I> Size of crypto header is 8192
[0203.536] I> MB2-Applet binary is read from storage
[0203.541] I> MB2-Applet binary integrity check is success
[0203.546] I> Binary MB2-Applet loaded successfully at 0x40000000 (0x41b40)
[0203.553] I> Task: Prepare MB2 params
[0203.557] I> BR-BCT Boot Chain Fields
[0203.560] I> 	 u32_non_gpio_select_boot_chain  : 0
[0203.565] I> 	 u32_num_boot_chains             : 0
[0203.570] I> 	 bf_bl_gpio_select_boot_chain_1b : 0
[0203.574] I> Task: Misc NV security settings
[0203.579] I> NVDEC sticky bits programming done
[0203.583] I> Successfully powergated NVDEC
[0203.587] I> Task: Disable/Reload WDT
[0203.591] I> Task: Program misc carveouts
[0203.594] I> SLCG Global override status := 0x0
[0203.599] I> MB1: MSS reconfig completed
[0203.603] W> Firewall readback mismatch
[09:22:18.547]收←◆
[0203.606] W> Firewall readback mismatch
[0203.610] W> Firewall readback mismatch
[0203.614] W> Firewall readback mismatch
[0203.617] W> Firewall readback mismatch
[0203.621] W> Firewall readback mismatch
[0203.625] W> Firewall readback mismatch
[0203.629] W> Firewall readback mismatch
[0203.632] W> Firewall readback mismatch
[0203.636] W> Firewall readback mismatch
I> Applet (version: 0.0.0.0-t234-54845784-8d394889)
I> t234-A01-0-Silicon (0x12347)
I> Emulation: 
I> Entry timestamp: 0xffffffff
I> Task: Pinmux init (0x4000062d)
I> Task: Boot device init (0x40001321)
I> Applet do storage init
I> Boot_device: QSPI_FLASH instance: 0
I> Qspi clock source : clk_m
I> QSPI-0l initialized successfully

[09:22:18.589]收←◆I> sdmmc DDR50 mode
I> sdmmc bdev is already initialized
E> Unknown device 7
E> Unknown device 8
I> Task: Partition Manager Init (0x40002d61)
I> Found 57 partitions in QSPI_FLASH (instance 0)
W> Cannot find any partition table for 00000003
 > PARTITION_MANAGER: Failed to publish partition.
I> Found 11 partitions in SDMMC_USER (instance 3)
I> Task: I2C register (0x400006a5)
I> Task: Register exit handlers (0x400005f5)
I> Task: Enter 3p server (0x40001925)
I> USB configuration success

[09:22:18.668]收←◆I> Populate chip info
I> RAM_CODE 0x4000001

[09:22:18.700]收←◆I> Populate eeprom info
I> Populate eeprom info for module cvm

[09:22:18.876]收←◆I> dump bct

[09:22:19.015]收←◆I> Rebooting : reboot-recovery


\0
[09:28:35.540]收←◆\0
[09:28:35.787]收←◆?
[0376.527] I> MB1 (version: 1.2.0.0-t234-54845784-562369e5)
[0376.533] I> t234-A01-0-Silicon (0x12347) Prod
[0376.537] I> Boot-mode : Coldboot
[0376.540] I> Entry timestamp: 0x00000000
[0376.544] I> last_boot_error: 0x0
[0376.547] I> BR-BCT: preprod_dev_sign: 0
[0376.551] I> rst_source: 0xb, rst_level: 0x1
[0376.555] I> Task: SE error check
[0376.558] I> Task: Bootchain select WAR set
[0376.562] I> Task: Enable SLCG
[0376.565] I> Task: CRC check
[0376.568] I> Skip FUSE records CRC check as records_integrity fuse is not burned
[0376.575] I> Task: Initialize MB2 params
[0376.579] I> MB2-params @ 0x40060000
[0376.583] I> Task: Crypto init
[0376.586] I> Task: Perform MB1 KAT tests
[0376.590] I> Task: NVRNG health check
[0376.593] I> NVRNG: Health check success
[0376.597] I> Task: MSS Bandwidth limiter settings for iGPU clients
[0376.603] I> Task: Enabling and initialization of Bandwidth limiter
[0376.609] I> No request to configure MBWT settings for any PC!
[0376.615] I> Task: Secure debug controls
[0376.619] I> Task: strap war set
[0376.622] I> Task: Initialize SOC Therm
[0376.625] I> Task: Program NV master stream id
[0376.630] I> Task: Verify boot mode
[0376.635] I> Task: Alias fuses
[0376.639] W> FUSE_ALIAS: Fuse alias on production fused part is not supported.
[0376.646] I> Task: Print SKU type
[0376.649] I> FUSE_OPT_CCPLEX_CLUSTER_DISABLE = 0x000001c0
[0376.654] I> FUSE_OPT_GPC_DISABLE = 0x00000000
[0376.659] I> FUSE_OPT_TPC_DISABLE = 0x00000001
[0376.663] I> FUSE_OPT_DLA_DISABLE = 0x00000000
[0376.667] I> FUSE_OPT_PVA_DISABLE = 0x00000000
[0376.672] I> FUSE_OPT_NVENC_DISABLE = 0x00000000
[0376.676] I> FUSE_OPT_NVDEC_DISABLE = 0x00000000
[0376.680] I> FUSE_OPT_FSI_DISABLE = 0x00000000
[0376.685] I> FUSE_OPT_EMC_DISABLE = 0x00000000
[0376.689] I> FUSE_BOOTROM_PATCH_VERSION = 0x7
[0376.693] I> FUSE_PSCROM_PATCH_VERSION = 0x7
[0376.697] I> FUSE_OPT_ADC_CAL_FUSE_REV = 0x2
[0376.701] I> FUSE_SKU_INFO_0 = 0xd2
[0376.705] I> FUSE_OPT_SAMPLE_TYPE_0 = 0x3 PS 
[0376.709] I> FUSE_PACKAGE_INFO_0 = 0x2
[0376.713] I> SKU: Prod
[0376.715] I> Task: Boost clocks
[0376.718] I> Initializing PLLC2 for AXI_CBB.
[0376.722] I> AXI_CBB : src = 35, divisor = 0
[0376.726] I> Task: Voltage monitor
[0376.729] I> VMON: Vmon re-calibration and fine tuning done
[0376.735] I> Task: UPHY init
[0376.740] I> HSIO UPHY init done
[0376.743] W> Skipping GBE UPHY config
[0376.746] I> Task: Boot device init
[0376.750] I> Boot_device: RCM
[0376.753] I> USB configuration success

[09:28:36.539]收←◆[0377.519] I> Task: TSC init
[0377.522] I> Task: 
[09:28:36.577]收←◆Load membct
[0377.525] I> RAM_CODE 0x4000001
[0377.528] I> Loading MEMBCT 
[0377.531] I> Slot: 0
[0377.533] I> Binary[0] block-0 (partition size: 0x40000)
[0377.538] I> Binary name: MEM-BCT-0
[0377.542] I> Size of crypto header is 8192
[0377.545] I> Size of crypto header is 8192

[09:28:36.940]收←◆[0377.564] I> BCH of MEM-BCT-0 read from storage
[0377.569] I> BCH address is : 0x40050000
[0377.572] I> MEM-BCT-0 header integrity check is success
[0377.578] I> Binary magic in BCH component 0 is MEM0
[0377.582] I> component binary type is 0
[0377.589] I> MEM-BCT-0 binary is read from storage
[0377.594] I> MEM-BCT-0 binary integrity check is success
[0377.599] I> Binary MEM-BCT-0 loaded successfully at 0x40040000 (0xe580)
[0377.605] I> RAM_CODE 0x4000001
[0377.611] I> RAM_CODE 0x4000001
[0377.615] I> Task: Load Page retirement list
[0377.619] I> Task: SDRAM params override
[0377.623] I> Task: Save mem-bct info
[0377.626] I> Task: Carveout allocate
[0377.629] I> Update CCPLEX IST carveout from MB1-BCT
[0377.634] I> ECC region[0]: Start:0x0, End:0x0
[0377.639] I> ECC region[1]: Start:0x0, End:0x0
[0377.643] I> ECC region[2]: Start:0x0, End:0x0
[0377.647] I> ECC region[3]: Start:0x0, End:0x0
[0377.651] I> ECC region[4]: Start:0x0, End:0x0
[0377.656] I> Non-ECC region[0]: Start:0x80000000, End:0x880000000
[0377.662] I> Non-ECC region[1]: Start:0x0, End:0x0
[0377.666] I> Non-ECC region[2]: Start:0x0, End:0x0
[0377.671] I> Non-ECC region[3]: Start:0x0, End:0x0
[0377.676] I> Non-ECC region[4]: Start:0x0, End:0x0
[0377.686] I> allocated(CO:44) base:0x849800000 size:0x36800000 align: 0x100000
[0377.693] I> allocated(CO:31) base:0x840000000 size:0x8000000 align: 0x8000000
[0377.701] I> allocated(CO:43) base:0x83c000000 size:0x4000000 align: 0x200000
[0377.708] I> allocated(CO:39) base:0x839e00000 size:0x2200000 align: 0x10000
[0377.715] I> allocated(CO:20) base:0x836000000 size:0x2000000 align: 0x2000000
[0377.722] I> allocated(CO:24) base:0x834000000 size:0x2000000 align: 0x2000000
[0377.729] I> allocated(CO:28) base:0x832000000 size:0x2000000 align: 0x2000000
[0377.736] I> allocated(CO:29) base:0x830000000 size:0x2000000 align: 0x2000000
[0377.743] I> allocated(CO:22) base:0x848000000 size:0x1000000 align: 0x1000000
[0377.750] I> allocated(CO:41) base:0x838e00000 size:0x1000000 align: 0x100000
[0377.757] I> allocated(CO:35) base:0x838000000 size:0xe00000 align: 0x10000
[0377.764] I> allocated(CO:02) base:0x849000000 size:0x800000 align: 0x800000
[0377.771] I> allocated(CO:03) base:0x82f800000 size:0x800000 align: 0x800000
[0377.778] I> allocated(CO:06) base:0x82f000000 size:0x800000 align: 0x800000
[0377.785] I> allocated(CO:56) base:0x82e800000 size:0x800000 align: 0x200000
[0377.792] I> allocated(CO:07) base:0x82e400000 size:0x400000 align: 0x400000
[0377.799] I> allocated(CO:33) base:0x82e000000 size:0x400000 align: 0x200000
[0377.806] I> allocated(CO:23) base:0x82de00000 size:0x200000 align: 0x200000
[0377.813] I> allocated(CO:01) base:0x82dd00000 size:0x100000 align: 0x100000
[0377.820] I> allocated(CO:04) base:0x82dc00000 size:0x100000 align: 0x100000
[0377.827] I> allocated(CO:05) base:0x82db00000 size:0x100000 align: 0x100000
[0377.834] I> allocated(CO:08) base:0x82da00000 size:0x100000 align: 0x100000
[0377.840] I> allocated(CO:09) base:0x82d900000 size:0x100000 align: 0x100000
[0377.847] I> allocated(CO:15) base:0x82d800000 size:0x100000 align: 0x100000
[0377.854] I> allocated(CO:17) base:0x82d700000 size:0x100000 align: 0x100000
[0377.861] I> allocated(CO:27) base:0x82d600000 size:0x100000 align: 0x100000
[0377.868] I> allocated(CO:42) base:0x82d500000 size:0x100000 align: 0x100000
[0377.875] I> allocated(CO:54) base:0x82d480000 size:0x80000 align: 0x80000
[0377.882] I> allocated(CO:34) base:0x82d470000 size:0x10000 align: 0x10000
[0377.889] I> allocated(CO:72) base:0x82d270000 size:0x200000 align: 0x10000
[0377.896] I> allocated(CO:46) base:0x800000000 size:0x20000000 align: 0x20000000
[0377.903] I> allocated(CO:47) base:0x82ce00000 size:0x400000 align: 0x200000
[0377.910] I> allocated(CO:48) base:0x82d250000 size:0x20000 align: 0x10000
[0377.917] I> allocated(CO:69) base:0x82d230000 size:0x20000 align: 0x10000
[0377.923] I> alloca
[09:28:37.002]收←◆ted(CO:49) base:0x82d220000 size:0x10000 align: 0x10000
[0377.930] I> allocated(CO:50) base:0x82d210000 size:0x10000 align: 0x10000
[0377.937] I> allocated(CO:52) base:0x82d200000 size:0x10000 align: 0x10000
[0377.944] I> NSDRAM base: 0x80000000, end: 0x82d270000, size: 0x7ad270000
[0377.950] I> Task: Thermal check
[0377.953] I> max_chip_limit = 105
[0377.957] I> min_chip_limit = -28
[0377.960] I> max temp read = 35
[0377.963] I> min temp read = 34
[0377.966] I> Task: Update FSI SCR with thermal fuse data
[0377.971] I> Task: Enable WDT 5th expiry
[0377.975] I> Task: I2C register
[0377.978] I> Task: Set I2C bus freq
[0377.981] I> Task: Reset FSI
[0377.984] I> Task: Pinmux init
\0
[09:28:37.260]收←◆\0
[09:28:37.620]收←◆?
[0000.062] I> MB1 (version: 0.23.0.0-t234-54845784-92215740)
[0000.067] I> t234-A01-0-Silicon (0x12347) Prod
[0000.071] I> Boot-mode : Coldboot
[0000.074] I> Emulation: 
[0000.077] I> Entry timestamp: 0x00000000
[0000.080] I> last_boot_error: 0x0
[0000.084] I> BR-BCT: preprod_dev_sign: 0
[0000.087] I> rst_source: 0x0, rst_level: 0x0
[0000.091] I> Task: CRC check (0x5001cf71)
[0000.095] I> Skip CRC check as records_integrity fuse is not burned
[0000.101] I> Task: Crypto init (0x5001c0d9)
[0000.105] I> Task: Secure debug controls (0x5000cb19)
[0000.110] I> Task: strap war set (0x5000b739)
[0000.115] I> strap value(0x4000401) set to 0x4000401
[0000.119] I> Task: Initialize SOC Therm (0x5001a509)
[0000.124] I> Task: Program NV master stream id (0x5000cad1)
[0000.130] I> Task: Verify boot mode (0xd482021)
[0000.136] I> Task: Alias fuses (0x50010749)
[0000.140] E> FUSE_ALIAS: Fuse alias on production fused part is not supported.
[0000.147] I> Task: Print SKU type (0x5000fba9)
[0000.151] I> FUSE_OPT_CCPLEX_CLUSTER_DISABLE = 0x000001c0
[0000.156] I> FUSE_OPT_GPC_DISABLE = 0x00000000
[0000.161] I> FUSE_OPT_TPC_DISABLE = 0x00000001
[0000.165] I> FUSE_OPT_DLA_DISABLE = 0x00000000
[0000.169] I> FUSE_OPT_EMC_DISABLE = 0x00000000
[0000.173] I> FUSE_BOOTROM_PATCH_VERSION = 0x7
[0000.178] I> FUSE_PSCROM_PATCH_VERSION = 0x7
[0000.182] I> FUSE_OPT_ADC_CAL_FUSE_REV = 0x2
[0000.186] I> FUSE_SKU_INFO_0 = 0xd2
[0000.189] I> FUSE_OPT_SAMPLE_TYPE_0 = 0x3 PS 
[0000.193] I> FUSE_PACKAGE_INFO_0 = 0x2
[0000.197] I> SKU: Prod
[0000.199] I> Task: Boost clocks (0x50013db1)
[0000.203] I> Initializing PLLC2 for AXI_CBB.
[0000.207] I> AXI_CBB : src = 35, divisor = 0
[0000.211] I> Task: Voltage monitor (0x50013dbd)
[0000.216] I> VMON: Vmon re-calibration and fine tuning done
[0000.221] I> Task: UPHY init (0x5000da39)
[0000.226] E> UPHY: UPHY lane info table is empty in MB1 BCT.
[0000.231] I> Task: Boot device init (0x50000a3d)
[0000.236] I> Boot_device: QSPI_FLASH instance: 0
[0000.240] I> Qspi clock source : pllc_out0
[0000.244] I> QSPI Flash: Macronix 64MB
[0000.248] I> QSPI-0l initialized successfully
[0000.252] I> Task: TSC init (0x5001ed35)
[0000.256] I> Task: Load membct (0x5001190d)
[0000.260] I> RAM_CODE 0x4000401
[0000.263] I> Loading MEM-BCT to SysRAM
[0000.267] I> Scratch RSV109: 0x00000001    active chain: 0
[0000.272] I> Slot: 0
[0000.274] I> Binary[0] block-0 (partition size: 0x40000)
[0000.279] I>  get_binary_info: Binary name: MEM-BCT-0
[0000.284] I> Size of crypto header is 8192
[0000.288] I> BCH load address is : 0x40050000
[0000.292] I> Size of crypto header is 8192
[0000.296] I> BCH of MEM-BCT-0 read from storage
[0000.301] I> BCH address is : 0x40050000
[0000.305] I> MEM-BCT-0 header integrity check is success
[0000.310] I> Binary magic in BCH component 0 is MEM0
[0000.315] I> component binary type is 0
[0000.319] I> MEM-BCT-0 binary is read from storage
[0000.324] I> MEM-BCT-0 binary integrity check is success
[0000.329] I> Binary MEM-BCT-0 loaded successfully at 0x40040000 (0xe580)
[0000.336] I> RAM_CODE 0x4000401
[0000.341] I> RAM_CODE 0x4000401
[0000.345] I> Task: Load Page retirement list (0x50011139)
[0000.350] I> Task: SDRAM params override (0x50011b79)
[0000.355] I> Task: Save mem-bct info (0x50014071)
[0000.360] I> Task: Carveout allocate (0x500140d5)
[0000.364] I> RCM blob carveout will not be allocated
[0000.369] I> ECC region[0]: Start:0x0, End:0x0
[0000.373] I> ECC region[1]: Start:0x0, End:0x0
[0000.377] I> ECC region[2]: Start:0x0, End:0x0
[0000.382] I> ECC region[3]: Start:0x0, End:0x0
[0000.386] I> ECC region[4]: Start:0x0, End:0x0
[0000.390] I> Non-ECC region[0]: Start:0x80000000, End:0x880000000
[0000.396] I> Non-ECC region[1]: Start:0x0, End:0x0
[0000.401] I> Non-ECC region[2]: Start:0x0, End:0x0
[0000.405] I> Non-ECC region[3]: Start:0x0, End:0x0
[0000.410] I> Non-ECC region[4]: Start:0x0, End:0x0
[0000.42
[09:28:37.970]收←◆0] I> allocated(CO:44) base:0x849800000 size:0x36800000 align: 0x100000
[0000.427] I> allocated(CO:31) base:0x840000000 size:0x8000000 align: 0x8000000
[0000.434] I> allocated(CO:39) base:0x83a000000 size:0x6000000 align: 0x200000
[0000.441] I> allocated(CO:20) base:0x838000000 size:0x2000000 align: 0x2000000
[0000.448] I> allocated(CO:24) base:0x836000000 size:0x2000000 align: 0x2000000
[0000.455] I> allocated(CO:28) base:0x834000000 size:0x2000000 align: 0x2000000
[0000.462] I> allocated(CO:29) base:0x832000000 size:0x2000000 align: 0x2000000
[0000.469] I> allocated(CO:43) base:0x830000000 size:0x2000000 align: 0x200000
[0000.476] I> allocated(CO:22) base:0x848000000 size:0x1000000 align: 0x1000000
[0000.483] I> allocated(CO:41) base:0x82f000000 size:0x1000000 align: 0x100000
[0000.490] I> allocated(CO:02) base:0x849000000 size:0x800000 align: 0x800000
[0000.497] I> allocated(CO:03) base:0x82e800000 size:0x800000 align: 0x800000
[0000.504] I> allocated(CO:06) base:0x82e000000 size:0x800000 align: 0x800000
[0000.511] I> allocated(CO:10) base:0x82d800000 size:0x800000 align: 0x800000
[0000.518] I> allocated(CO:56) base:0x82d000000 size:0x800000 align: 0x200000
[0000.525] I> allocated(CO:07) base:0x82cc00000 size:0x400000 align: 0x400000
[0000.532] I> allocated(CO:33) base:0x82c800000 size:0x400000 align: 0x200000
[0000.539] I> allocated(CO:47) base:0x82c400000 size:0x400000 align: 0x200000
[0000.546] I> allocated(CO:72) base:0x82c200000 size:0x200000 align: 0x10000
[0000.553] I> allocated(CO:01) base:0x82c100000 size:0x100000 align: 0x100000
[0000.560] I> allocated(CO:04) base:0x82c000000 size:0x100000 align: 0x100000
[0000.567] I> allocated(CO:05) base:0x82bf00000 size:0x100000 align: 0x100000
[0000.573] I> allocated(CO:08) base:0x82be00000 size:0x100000 align: 0x100000
[0000.580] I> allocated(CO:09) base:0x82bd00000 size:0x100000 align: 0x100000
[0000.587] I> allocated(CO:15) base:0x82bc00000 size:0x100000 align: 0x100000
[0000.594] I> allocated(CO:17) base:0x82bb00000 size:0x100000 align: 0x100000
[0000.601] I> allocated(CO:23) base:0x82ba00000 size:0x100000 align: 0x100000
[0000.608] I> allocated(CO:27) base:0x82b900000 size:0x100000 align: 0x100000
[0000.615] I> allocated(CO:42) base:0x82b800000 size:0x100000 align: 0x100000
[0000.622] I> allocated(CO:54) base:0x82b780000 size:0x80000 align: 0x80000
[0000.629] I> allocated(CO:26) base:0x82b740000 size:0x40000 align: 0x2000
[0000.635] I> allocated(CO:48) base:0x82b720000 size:0x20000 align: 0x10000
[0000.642] I> allocated(CO:69) base:0x82b700000 size:0x20000 align: 0x10000
[0000.649] I> allocated(CO:34) base:0x82b6f0000 size:0x10000 align: 0x10000
[0000.656] I> allocated(CO:35) base:0x82b6e0000 size:0x10000 align: 0x10000
[0000.662] I> allocated(CO:49) base:0x82b6d0000 size:0x10000 align: 0x10000
[0000.669] I> allocated(CO:50) base:0x82b6c0000 size:0x10000 align: 0x10000
[0000.676] I> allocated(CO:52) base:0x82b6b0000 size:0x10000 align: 0x10000
[0000.683] I> Task: Thermal check (0x5001fba1)
[0000.687] I> max_chip_limit = 115
[0000.690] I> min_chip_limit = -30
[0000.693] I> max temp read = 35
[0000.696] I> min temp read = 34
[0000.699] I> Task: Update FSI SCR with thermal fuse data (0x5001fc3d)
[0000.705] I> Task: Enable WDT 5th expiry (0x5001f929)
[0000.710] I> Task: Disable WDT globally (0x5001f965)
[0000.715] I> Task: I2C register (0x50000a31)
[0000.719] I> Task: Reset FSI (0x50013db9)
[0000.723] I> Task: Pinmux init (0x50013219)
[0000.727] I> Task: Prod config init (0x50013631)
[0000.732] I> Task: Pad voltage init (0x500132a5)
[0000.736] I> Task: Prod init (0x500136d5)
[0000.740] I> Task: Common rail init (0x50013bd1)
[0000.745] W>  Thermal config not found in BCT
[0000.749] W>  Generic i2c config not found in BCT
[0000.753] W>  Platform rail config not found in BCT
[0000.759] W> DEVICE_PROD: module = 13, instance = 4 not found in device prod.
[0000.767] W>  MEMIO rail config not f
[09:28:38.056]收←◆ound in BCT
[0000.772] I> Task: Mem clock src (0x500119c5)
[0000.776] I> Task: Misc. board config (0x50013c29)
[0000.781] W>  Platform config not found in BCT
[0000.785] I> Task: SDRAM init (0x500119c9)
[0000.791] I> SDRAM-params @ 0xd485000
[0000.795] I> MSS code-drop: NvBootSdramInit
[0000.799] I> MSS CAR: PLLM/HUB programming for MemoryType: 4 and MemBctRevision: 8
[0000.806] I> MSS CAR: Init PLLM
[0000.809] I> MSS CAR: Init PLLHUB
[0000.814] I> Encryption:   MTS: en, TX: dis, VPR: dis, GSC: en
[0000.826] I> mb1_sdram_init Done !
[0000.829] I> SDRAM Size in Total 0x800000000
[0000.833] I> Task: Dram Ecc scrub (0x50011261)
[0000.838] I> Task: DRAM alias check (0x50011b71)
[0000.869] I> Task: Program NSD
[09:28:38.111]收←◆RAM carveout (0x50014921)
[0000.875] I> NSDRAM carveout encryption is disabled
[0000.880] I> Program NSDRAM carveout
[0000.884] I> Task: Register checker (0x50011b75)
[0000.893] I> Task: Enable clock-mon (0x5001ed25)
[0000.910] I> FMON: 
[09:28:38.240]收←◆Fmon re-programming done
[0000.914] I> Task: Mapper init (0x5001d451)
[0000.919] I> Task: SC7 Context Init (0x5001f02d)
[0000.926] I> Task: CCPLEX IST init (0x5000d335)
[0000.932] I> Task: CPU WP0 (0x5000c635)
[0000.937] I> Loading MCE
[0000.940] I> Scratch RSV109: 0x00000001    active chain: 0
[0000.945] I> Slot: 0
[0000.948] I> Binary[8] block-0 (partition size: 0x80000)
[0000.954] I>  get_binary_info: Binary name: MCE
[0000.958] I> Size of crypto header is 8192
[0000.963] I> BCH load address is : 0x4003e000
[0000.968] I> Size of crypto header is 8192
[0000.973] I> BCH of MCE read from storage
[0000.977] I> BCH address is : 0x4003e000
[0000.983] I> MCE header integrity check is success
[0000.988] I> Binary magic in BCH component 0 is MTSM
[0000.993] I> component binary type is 8
[0000.997] I> Size of crypto header is 8192
[0001.004] I> MCE binary is read from storage
[0001.009] I> MCE binary integrity check is success
[0001.014] I> Binary MCE loaded successfully at 0x40000000 (0x2c080)
[0001.022] I> Size of crypto header is 8192
[0001.036] I> Size of crypto header is 8192

[09:28:38.269]收←◆[0001.041] I> Sending WP0 mailbox command to PSC
[0001.051] I> Task: MB1 fixed firewalls (0x5001e55d)

[09:28:38.350]收←◆[0001.071] I> Task: Load bpmp-fw (0x5001e801)
[0001.077] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.082] I> Slot: 0
[0001.085] I> Binary[15] block-0 (partition size: 0x180000)
[0001.091] I>  get_binary_info: Binary name: BPMP_FW
[0001.096] I> Size of crypto header is 8192
[0001.101] I> BCH load address is : 0x807fe000
[0001.106] I> Size of crypto header is 8192
[0001.111] I> BCH of BPMP_FW read from storage
[0001.116] I> BCH address is : 0x807fe000
[0001.121] I> BPMP_FW header integrity check is success
[0001.127] I> Binary magic in BCH component 0 is BPMF
[0001.132] I> component binary type is 15
[0001.136] I> Size of crypto header is 8192

[09:28:38.782]收←◆[0001.151] I> BPMP_FW binary is read from storage
[0001.159] I> BPMP_FW binary integrity check is success
[0001.164] I> Binary BPMP_FW loaded successfully at 0x80000000 (0xfb3c0)
[0001.172] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.178] I> Slot: 0
[0001.180] I> Binary[16] block-10000 (partition size: 0x400000)
[0001.187] I>  get_binary_info: Binary name: BPMP_FW_DTB
[0001.193] I> Size of crypto header is 8192
[0001.197] I> BCH load address is : 0x807fc000
[0001.203] I> Size of crypto header is 8192
[0001.208] I> BCH of BPMP_FW_DTB read from storage
[0001.213] I> BCH address is : 0x807fc000
[0001.218] I> BPMP_FW_DTB header integrity check is success
[0001.224] I> Binary magic in BCH component 0 is BPMD
[0001.229] I> component binary type is 16
[0001.233] I> Size of crypto header is 8192
[0001.240] I> BPMP_FW_DTB binary is read from storage
[0001.246] I> BPMP_FW_DTB binary integrity check is success
[0001.251] I> Binary BPMP_FW_DTB loaded successfully at 0x807db9f0 (0x20440)
[0001.260] I> Task: Load psc-fw (0x5001ea0d)
[0001.266] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.272] I> Slot: 0
[0001.274] I> Binary[17] block-0 (partition size: 0xc0000)
[0001.280] I>  get_binary_info: Binary name: PSC_FW
[0001.285] I> Size of crypto header is 8192
[0001.290] I> BCH load address is : 0x80ffe000
[0001.295] I> Size of crypto header is 8192
[0001.300] I> BCH of PSC_FW read from storage
[0001.305] I> BCH address is : 0x80ffe000
[0001.310] I> PSC_FW header integrity check is success
[0001.316] I> Binary magic in BCH component 0 is PFWP
[0001.321] I> component binary type is 17
[0001.325] I> Size of crypto header is 8192
[0001.335] I> PSC_FW binary is read from storage
[0001.341] I> PSC_FW binary integrity check is success
[0001.347] I> Binary PSC_FW loaded successfully at 0x80000000 (0x7d000)
[0001.355] I> Task: Load nvdec-fw (0x5001ea81)
[0001.361] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.367] I> Slot: 0
[0001.369] I> Binary[7] block-0 (partition size: 0x100000)
[0001.375] I>  get_binary_info: Binary name: NVDEC
[0001.380] I> Size of crypto header is 8192
[0001.385] I> BCH load address is : 0x800fe000
[0001.390] I> Size of crypto header is 8192
[0001.395] I> BCH of NVDEC read from storage
[0001.399] I> BCH address is : 0x800fe000
[0001.405] I> NVDEC header integrity check is success
[0001.410] I> Binary magic in BCH component 0 is NDEC
[0001.416] I> component binary type is 7
[0001.420] I> Size of crypto header is 8192
[0001.427] I> NVDEC binary is read from storage
[0001.432] I> NVDEC binary integrity check is success
[0001.437] I> Binary NVDEC loaded successfully at 0x80000000 (0x35000)
[0001.448] I> Task: Load tsec-fw (0x5001ec6d)
[0001.453] I> TSEC-FW load support not enabled
[0001.458] I> Task: Program misc carveouts (0x5001445d)
[0001.464] I> Program IPC carveouts
[0001.471] I> Task: GPIO interrupt map (0x50013cc5)
[0001.478] I> Task: SC7 context save (0x5001f161)
[0001.483] I> NV_SC7 Context addr: 0xa0000000
[0001.489] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.495] I> Slot: 0
[0001.497] I> Binary[27] block-0 (partition size: 0x100000)
[0001.503] I>  get_binary_info: Binary name: BR_BCT
[0001.508] I> Size of crypto header is 8192
[0001.513] I> Size of crypto header is 8192
[0001.518] I> BR_BCT binary is read from storage
[0001.523] I> BR_BCT binary integrity check is success
[0001.529] I> Binary BR_BCT loaded successfully at 0xa0000000 (0x2000)
[0001.536] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.542] I> Slot: 0
[0001.545] I> Binary[13] block-0 (partition size: 0x30000)
[0001.551] I>  get_binary_info: Binary name: SC7-FW
[0001.556] I> Size of crypto header is 8192
[0001.560] I> Size of crypto header is 8192
[0001.565] I> BCH load address is : 0xa0002000
[0001.570] I> Size of crypto header is 8192
[0001.575] I> BCH of SC7-FW read from storage
[0001.580] I> BCH addr
[09:28:38.929]收←◆ess is : 0xa0002000
[0001.585] I> SC7-FW header integrity check is success
[0001.591] I> Binary magic in BCH component 0 is WB0B
[0001.596] I> component binary type is 13
[0001.600] I> Size of crypto header is 8192
[0001.606] I> SC7-FW binary is read from storage
[0001.612] I> SC7-FW binary integrity check is success
[0001.617] I> Binary SC7-FW loaded successfully at 0xa0004000 (0x25460)
[0001.626] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.631] I> Slot: 0
[0001.634] I> Binary[22] block-0 (partition size: 0x30000)
[0001.640] I>  get_binary_info: Binary name: PSC_RF
[0001.645] I> Size of crypto header is 8192
[0001.649] I> Size of crypto header is 8192
[0001.654] I> BCH load address is : 0xa0029460
[0001.660] I> Size of crypto header is 8192
[0001.664] I> BCH of PSC_RF read from storage
[0001.669] I> BCH address is : 0xa0029460
[0001.674] I> PSC_RF header integrity check is success
[0001.680] I> Binary magic in BCH component 0 is PSCR
[0001.685] I> component binary type is 22
[0001.689] I> Size of crypto header is 8192
[0001.695] I> PSC_RF binary is read from storage
[0001.701] I> PSC_RF binary integrity check is success
[0001.706] I> Binary PSC_RF loaded successfully at 0xa002b460 (0x1bd20)
[0001.726] I> Scratch RSV109: 0x00000
[09:28:39.219]收←◆001    active chain: 0
[0001.732] I> Slot: 0
[0001.734] I> Binary[14] block-0 (partition size: 0x20000)
[0001.740] I>  get_binary_info: Binary name: MB2_RF
[0001.746] I> Size of crypto header is 8192
[0001.750] I> Size of crypto header is 8192
[0001.755] I> BCH load address is : 0xa008e240
[0001.760] I> Size of crypto header is 8192
[0001.765] I> BCH of MB2_RF read from storage
[0001.770] I> BCH address is : 0xa008e240
[0001.775] I> MB2_RF header integrity check is success
[0001.780] I> Binary magic in BCH component 0 is MB2R
[0001.786] I> component binary type is 14
[0001.790] I> Size of crypto header is 8192
[0001.796] I> MB2_RF binary is read from storage
[0001.801] I> MB2_RF binary integrity check is success
[0001.807] I> Binary MB2_RF loaded successfully at 0xa0090240 (0x1bdc0)
[0001.816] E> FUSE_ALIAS: Fuse alias on production fused part is not supported.
[0001.823] I> SC7 context fuse-bypass data is empty
[0001.831] I> SC7 context save done
[0001.835] I> Task: Load MB2/Applet/FSKP (0x5000d451)
[0001.841] I> Loading MB2
[0001.844] I> Scratch RSV109: 0x00000001    active chain: 0
[0001.850] I> Slot: 0
[0001.852] I> Binary[6] block-0 (partition size: 0x80000)
[0001.858] I>  get_binary_info: Binary name: MB2
[0001.863] I> Size of crypto header is 8192
[0001.868] I> BCH load address is : 0x8007e000
[0001.873] I> Size of crypto header is 8192
[0001.878] I> BCH of MB2 read from storage
[0001.882] I> BCH address is : 0x8007e000
[0001.888] I> MB2 header integrity check is success
[0001.893] I> Binary magic in BCH component 0 is MB2B
[0001.898] I> component binary type is 6
[0001.902] I> Size of crypto header is 8192
[0001.911] I> MB2 binary is read from storage
[0001.917] I> MB2 binary integrity check is success
[0001.922] I> Binary MB2 loaded successfully at 0x80000000 (0x686c0)
[0001.930] I> Task: Map CCPLEX SHARED carveout (0x5000d521)
[0001.937] I> Task: Prepare MB2 params (0x5000d5dd)
[0001.946] I> MB2-params @ 0x40060000
[0001.954] I> BR-BCT Boot Chain Fields
[0001.958] I> 	 u32_non_gpio_select_boot_chain  : 0
[0001.963] I> 	 u32_num_boot_chains             : 2
[0001.968] I> 	 bf_bl_gpio_select_boot_chain_1b : 0
[0001.974] I> Task: Dram ecc test (0x500112cd)
[0001.979] I> Task: Misc NV security settings (0x5000ced5)
[0001.986] I> NVDEC sticky bits programming done
[0001.991] I> Task: Disable/Reload WDT (0x5001f991)
[0001.997] I> Programmed SLCG global override := 0x0
[0002.002] I> MB1: MSS reconfig completed

[09:28:39.321]收←◆I> MB2 (version: 0.0.0.0-t234-54845784-e33bc3dc)
I> t234-A01-0-Silicon (0x12347)
I> Boot-mode : Coldboot
I> Emulation: 
I> Entry timestamp: 0x001f1f97
I> Regular heap: [base:0x40040000, size:0x10000]
I> DMA heap: [base:0x82d000000, size:0x800000]
I> Task: ARI update carveout TZDRAM (0x50001e6c)
I> Task: Enable hot-plug capability (0x50020e7c)
I> Task: PSC mailbox init (0x50011ed0)
I> Task: Crypto init (0x5000513c)
I> Task: Enable GP-SE clock (0x50001fd0)
I> Task: I2C register (0x50001e30)
I> Task: Map CCPLEX_INTERWORLD_SHMEM carveout (0x50001e18)
I> Task: Boot device init (0x50001d60)
I> Boot_device: QSPI_FLASH instance: 0
I> Qspi clock source : pllc_out0
I> QSPI-0l initialized successfully

[09:28:39.505]收←◆I> Task: Partition Manager Init (0x50001d5c)
I> Found 57 partitions in QSPI_FLASH (instance 0)
W> Cannot find any partition table for 00000003
 > PARTITION_MANAGER: Failed to publish partition.
I> Found 11 partitions in SDMMC_USER (instance 3)
I> Task: Load and authenticate registered FWs (0x50017428)
I> Task: Load AUXP FWs (0x50020a1c)
I> Successfully register SPE FW load task with MB2 loader
I> Skipping SCE FW load
I> Successfully register RCE FW load task with MB2 loader
I> Successfully register DCE FW load task with MB2 loader
I> Unpowergating APE
I> Unpowergate done
I> Successfully register APE FW load task with MB2 loader
I> Skipping FSI FW load
I> Successfully register XUSB FW load task with MB2 loader
I> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_spe-fw
I> Size of partition: 589824
I> Binary@ device:3/0 block-55040 (partition size: 0x90000), name: A_spe-fw
I> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_rce-fw
I> Size of partition: 1048576
I> Binary@ device:3/0 block-56192 (partition size: 0x100000), name: A_rce-fw
I> spe: Authentication Finalize Done
I> Binary spe loaded successfully at 0x82be00000
I> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_dce-fw
I> Size of partition: 5242880
I> Binary@ device:3/0 block-44800 (partition size: 0x500000), name: A_dce-fw
I> rce: Authentication Finalize Done
I> Binary rce loaded successfully at 0x82bb00000
I> dce : oem authentication of header done
I> dce : meta-blob integrity check is success.
I> dce : will be decompressed at 0x838000000
I> version 1 Bin 1 BCheckSum 0 content_size 0 Content ChkSum 1 reserved_00  0
I> Reserved10 0 BlockMaxSize 5 Reserved11 0
I> dce : decompressed to 9477552 bytes

[09:28:39.693]收←◆I> dce: plain binary integrity check is success
I> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_adsp-fw
I> Size of partition: 2097152
I> Binary@ device:3/0 block-58240 (partition size: 0x200000), name: A_adsp-fw
I> dce: Authentication Finalize Done
I> Binary dce loaded successfully at 0x838000000
I> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_xusb-fw
I> Size of partition: 262144
I> Binary@ device:3/0 block-9472 (partition size: 0x40000), name: A_xusb-fw
I> ape: Authentication Finalize Done
I> Binary ape loaded successfully at 0x82cc00000
I> xusb: Authentication Finalize Done
I> Binary xusb loaded successfully at 0x82bf00000
I> Task: Carveout setup (0x50019c94)
I> Program remaining OEM carveouts
I> Task: Enable FSITHERM (0x50011da4)
I> Task: Enable FSI VMON (0x50011944)
I> FSI VMON: FSI Vmon re-calibration and fine tuning done
I> Task: Validate FSI Therm readings (0x5001199c)
I> FSITHERM max temp = 35
I> FSITHERM min temp = 34
I> Task: Restore XUSB sec (0x50001d30)
I> Task: Enable FSI SE clock (0x5001232c)
I> Enable FSI-SE clock and 10ms delay...
I> Task: Initialize SBSA UART CAR (0x50001f34)
I> Task: Initialize CPUBL Params (0x50013384)
I> CPUBL-params @ 0x834000000
I> Task: Prepare eeprom data (0x50013140)

[09:28:39.736]收←◆I> Task: OEM firewalls (0x5001df14)
W> mb2_unpowergate_ape: skip! APE is in unpowergated state
I> OEM firewalls configured
I> Task: Unhalt AUXPs (0x50020c84)
I> Unhalting SPE..
I> Enabling combined UART 
\0
[09:28:40.100]收←◆?鄐pe: early_init
vic initialized
tsc initialized
aon lic initialized
spe: tag is 2e3d77fae66a40ac8e7a91531ae7d9b3
spe: SafeRTOS v8.4
spe: init
scheduler initialized
aon hsp initialized
tag initialized
tcu initialized
bpmp ipc initialized
spe: late init
cpu_nic clock initialized
apb clock initialized
pm initialized
bpmp hsp initialized
top1 hsp initialized
ccplex ipc initialized
spe: start scheduler
?
I> Task: Trigger mailbox for PSC-BL1 exit (0x50011f50)
I> Sending opcode 0x4d420802 to psc
鏘NFO: Entering psc_monitor_init!
INFO: GSC22 BOM:0x848000000 SIZE:0x1000000 CLIENT_ACCESS1:00180000
INFO: PSCFW BUILD VERSION: e061f86-9e1f578-2508c43-dev-t234
INFO: mstatus:0xa00000808
INFO: Supervisor entry_point:c108c00
酙> Received ACK from psc
I> Task: Sta鏘NFO: MONITOR: user task addr:0x848022000, blob offset:0x00020000
?
醨t secure NOR provision (0x50014924)
I> Task: Load FSI keyblob (0x50012368)
I> Skipping FSI key blob copy
I> Task: Unhalt AUXPs (0x50020c8c)
I> SCE unhalt skipped
I> Unhalting RCE
I> RCE unhalt successful
I> DCE unhalt successful
I> APE unhalt skipped
I> FSI unhalt skipped
I> Task: Load CPUBL (0x5001347c)
I> Task: Load TOS (0x50013b38)
I> Task: Load and authenticate registered FWs (0x50017428)
I> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_cpu-bo錥     2.390748] Camera-FW on t234-rce-safe started
鈈pmp: init
bpmp: base binary md5 is eac380526d68ff45ffc86d0feae98e88
bpmp: combined binary md5 is 888a114dda6bea50b6c6bb224445ac85
bpmp: firmware tag is 888a114dda6bea50b6c6-eac380526d6
initialized vwdt
initialized mail_early
initialized fuse
initialized vfre錞CU early console ena鏘NFO: MONITOR: populated user images:19
INFO: mret to Supervisor!
INFO: psc supervisor init.
INFO: psc_irq_init...
INFO: enter idle task.
鈒
initialized hwwdt
initialized adc
fmon_populate_monitors: found 199 monitors
initialized fmon
initialized mc
initialized reset
initialized uphy_early
initialized emc_early
471 clocks registered
initialized clk_mach
initialized clk_cal_early錬led.
?
initialized clk_mach_early_config
initialized io_dpd
initialized thermal
initialized soctherm
initialized tj_init
initialized regime
initialized i2c
vrmon_dt_init: vrmon node not found
vrmon_chk_boot_state: found 0 rail monitors
initialized vrmon
initialized regulator
醥tloader
I> Size of part?
醝tion: 36700鈏nitialized avfs_clk_platform
initialized powergate
?6
I> Binary@ device:3/0 block-24832 (partition size: 0x380000), name: A_cpu-bootloa鈏nitialized dvs
initialized clk_mach_config
initialized pm
initialized suspend
initialized strap
initialized emc
initialized emc_mrq
醖er
鈏nitialized clk_cal
initialized uphy_dt
initialized uphy_mrq
start PLL 8 calibration timeout

FATAL ERROR [FILE=platform/drivers/uphy/uphy-tegra234.c, ERR_UID=2251]: start PLL 8 calibration failed
r0_usr	0x50090e6f
r1_usr	0x000008cb
r2_usr	0x500382f4
r3_usr	0x50181edc
r4_usr	0x500020a8
r5_usr	0x500382f4
r6_usr	0x000008cb
r7_usr	0x50090e6f
r8_usr	0x50181edc	r8_fiq	0x00000000
r9_usr	0x50204550	r9_fiq	0x00000000
r10_usr	0x00000009	r10_fiq	0x00000000
r11_usr	0x50080006	r11_fiq	0x00000000
r12_usr	0xc0000000	r12_fiq	0x00000000
sp_usr	0x50181ec0	sp_fiq	0x5001a620	sp_irq	0x5001a600
sp_svc	0x5001a400	sp_abt	0x5001ac00	sp_und	0x5001ab70
lr_usr	0x50003205	lr_fiq	0x00000000	lr_irq	0x5006dfc0
lr_svc	0x5000a6ec	lr_abt	0x00000000	lr_und	0x500020ac
pc 0x500020a8
spsr 0x20000010
fpscr 0x20000010
00: base: 50000000 size: 00800000 XN P_RW U_RW Non-shareable outer: WB, no WA inner: WB, no WA
01: base: 00000000 size: 40000000 XN P_RW U_RW Shareable strongly-ordered
02: base: 00000000 size: 00000040 X  P_RO U_NA Non-shareable outer: WB, no WA inner: WB, no WA
03: base: 50000000 size: 00010000 X  P_RO U_RO Non-shareable outer: WB, no WA inner: WB, no WA
04.1: base: 50020000 size: 00020000 X  P_RO U_RO Non-shareabl
[09:28:40.419]收←◆e outer: WB, no WA inner: WB, no WA
04.2: base: 50040000 size: 00020000 X  P_RO U_RO Non-shareable outer: WB, no WA inner: WB, no WA
04.3: base: 50060000 size: 00020000 X  P_RO U_RO Non-shareable outer: WB, no WA inner: WB, no WA
04.4: base: 50080000 size: 00020000 X  P_RO U_RO Non-shareable outer: WB, no WA inner: WB, no WA
04.5: base: 500a0000 size: 00020000 X  P_RO U_RO Non-shareable outer: WB, no WA inner: WB, no WA
05.6: base: 500b8000 size: 00004000 XN P_RW U_RW Non-shareable outer: WB, no WA inner: WB, no WA
05.7: base: 500bc000 size: 00004000 XN P_RW U_RW Non-shareable outer: WB, no WA inner: WB, no WA
06: base: 50180000 size: 00080000 XN P_RO U_NA Non-shareable outer: WB, no WA inner: WB, no WA
07.7: base: 507c0000 size: 00040000 XN P_RO U_RO Non-shareable outer: WB, no WA inner: WB, no WA
08: base: 50202000 size: 00002000 XN P_RW U_RW Non-shareable outer: WT, no WA inner: WT, no WA
10: base: 40070000 size: 00010000 XN P_RW U_RW Non-shareable outer: WB, no WA inner: WB, no WA
15: base: 50180000 size: 00002000 XN P_RW U_RW Non-shareable outer: WB, no WA inner: WB, no WA
Bootstrap@0x502190e0 sp 0x50181ec0 stack: 50180000 - 50181ffc
Per task regions for Bootstrap
03: base: 50180000 size: 00002000 XN P_RW U_RW Non-shareable outer: WB, no WA inner: WB, no WA
Enable MMIO: 1, Enable data R/W: 1
call stack:
sp 0x50181ec0 pc 0x500020a8
sp 0x50181ec0 pc 0x50003204
sp 0x50181ed8 pc 0x500382e8
sp 0x50181f20 pc 0x500390e0
sp 0x50181f70 pc 0x500304ae
sp 0x50181fb0 pc 0x5002ebcc
sp 0x50181ff0 pc 0x5006909e
sp 0x50181ff8 pc 0xaaaaaaaa
eht_idx_find: 0xaaaaaaaa not a valid code address
no eidx for 0xaaaaaaaa
酙> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_secure-os
I> Size of partition: 4194304
I> Binary@ device:3/0 block-32000 (partition size: 0x400000), name: A_secure-os
I> MB2-params @ 0x40060000
I> cpubl: Authentication Finalize Done
I> Binary cpubl loaded successfully at 0x82c400000
I> tos: Authentication Finalize Done
I> Binary tos loaded successfully at 0x831e06000
I> Relocating OP-TEE dtb from: 0x831eff700 to 0x82b700000, size: 0x996
I> [0] START: 0x80000000, SIZE: 0x7ab600000
I> [1] START: 0x82c400000, SIZE: 0x400000
I> [2] START: 0x82d000000, SIZE: 0x800000
I> Setting NS memory ranges to OP-TEE dtb finished.
I> Scratch RSV109: 0x00000001    active chain: 0
I> Partition name: A_eks
I> Size of partition: 262144
I> Binary@ device:3/0 block-44288 (partition size: 0x40000), name: A_eks
I> eks: Authentication Finalize Done
I> Binary eks loaded successfully at 0x82d000400
I> EKB detected (length: 0x410) @ VA:0x82d000400
I> Task: Prepare TOS params (0x50013ab0)
I> Setting EKB blob info to OPTEE dtb finished.
I> Setting OPTEE arg3: 0x82b700000
I> Task: OEM SC7 context save (0x500146bc)
I> oem sc7 context saved
I> Task: Disable MSS perf stats (0x50020d18)
I> Task: Program display sticky bits (0x50020c94)
I> Task: Storage device deinit (0x50001ed8)
I> Task: SMMU external bypass disable (0x50011eb4)
I> Task: SMMU init (0x50011dd0)
I> Task: Program CBB PCIE AMAP regions (0x50014b08)
I> Task: Program GICv3 registers (0x50020db8)
I> Task: Audit firewall settings (0x5001e1c0)
I> Task: Bootchain failure check (0x500026a4)
I> Current Boot-Chain Slot: 0
I> BR-BCT Boot-Chain is 0, and status is 1. Set UPDATE_BRBCT bit to 0
I> MB2 finished

銷OTICE:  BL31: v2.6(release):4fa405dbd
NOTICE:  BL31: Built : 20:16:55, Aug 10 2022
I/TC
[09:28:40.437]收←◆: 

[09:28:40.467]收←◆I/TC: Non-secure external DT found

[09:28:40.547]收←◆I/TC: OP-TEE version: 3.16 (gcc version 9.3.0 (Buildroot 2020.08)) #2 Thu Aug 11 03:23:19 UTC 2022 aarch64
I/TC: WARNING: This OP-TEE configuration might be insecure!
I/TC: WARNING: Please check https://optee.readthedocs.io/en/latest/architecture/porting_guidelines.html
I/TC: Primary CPU initializing

[09:28:40.739]收←◆I/TC: WARNING: Test OEM keys are being used!
I/TC: This is only for TZ-SE testing and should NOT be used for a shipping product!
E/TC:00 0 jetson_user_key_pta_init:700 jetson_user_key_pta_init: Failed (f0100006).
E/TC:00 0 call_initcalls:43 Initcall __text_start + 0x000dab50 failed
I/TC: Primary CPU switching to normal world boot

[09:28:42.019]收←◆錏RROR: camera-ip/isp5/isp5.c:1977 [isp5_pm_init] "ERROR: Failed to turn isp power on"
BUG: core/init/init.c:85 [init_all] "*** FIRMWARE INIT FAILED AT LEVEL 95 ***"

[09:28:45.944]收←◆?
Jetson UEFI firmware (version 1.0-d7fb19b built on 2022-08-10T20:18:13-07:00)

[09:28:46.168]收←◆

[09:28:46.584]收←◆

[09:28:46.728]收←◆


[09:28:46.808]收←◆








[09:28:46.923]收←◆