[0000.065] I> MB1 (version: 1.4.0.1-t234-54845784-08e631ca) [0000.070] I> t234-A01-0-Silicon (0x12347) Prod [0000.074] I> Boot-mode : Coldboot [0000.077] I> Entry timestamp: 0x00000000 [0000.081] I> last_boot_error: 0x0 [0000.084] I> BR-BCT: preprod_dev_sign: 0 [0000.088] I> rst_source: 0xb, rst_level: 0x1 [0000.092] I> Task: SE error check [0000.095] I> Task: Bootchain select WAR set [0000.099] I> Task: Enable SLCG [0000.102] I> Task: CRC check [0000.105] I> Task: Initialize MB2 params [0000.109] I> MB2-params @ 0x40060000 [0000.113] I> Task: Crypto init [0000.116] I> Task: Perform MB1 KAT tests [0000.120] I> Task: NVRNG health check [0000.123] I> NVRNG: Health check success [0000.127] I> Task: MSS Bandwidth limiter settings for iGPU clients [0000.133] I> Task: Enabling and initialization of Bandwidth limiter [0000.139] I> No request to configure MBWT settings for any PC! [0000.145] I> Task: Secure debug controls [0000.149] I> Task: strap war set [0000.152] I> Task: Initialize SOC Therm [0000.155] I> Task: Program NV master stream id [0000.160] I> Task: Verify boot mode [0000.165] I> Task: Alias fuses [0000.169] W> FUSE_ALIAS: Fuse alias on production fused part is not supported. [0000.176] I> Task: Print SKU type [0000.179] I> FUSE_OPT_CCPLEX_CLUSTER_DISABLE = 0x000001c8 [0000.184] I> FUSE_OPT_GPC_DISABLE = 0x00000001 [0000.189] I> FUSE_OPT_TPC_DISABLE = 0x0000000f [0000.193] I> FUSE_OPT_DLA_DISABLE = 0x00000002 [0000.197] I> FUSE_OPT_PVA_DISABLE = 0x00000000 [0000.201] I> FUSE_OPT_NVENC_DISABLE = 0x00000000 [0000.206] I> FUSE_OPT_NVDEC_DISABLE = 0x00000000 [0000.210] I> FUSE_OPT_FSI_DISABLE = 0x00000001 [0000.215] I> FUSE_OPT_EMC_DISABLE = 0x0000000c [0000.219] I> FUSE_BOOTROM_PATCH_VERSION = 0x7 [0000.223] I> FUSE_PSCROM_PATCH_VERSION = 0x7 [0000.227] I> FUSE_OPT_ADC_CAL_FUSE_REV = 0x2 [0000.231] I> FUSE_SKU_INFO_0 = 0xd4 [0000.235] I> FUSE_OPT_SAMPLE_TYPE_0 = 0x3 PS [0000.239] I> FUSE_PACKAGE_INFO_0 = 0x2 [0000.242] I> SKU: Prod [0000.245] I> Task: Boost clocks [0000.248] I> Initializing PLLC2 for AXI_CBB. [0000.252] I> AXI_CBB : src = 35, divisor = 0 [0000.256] I> Task: Voltage monitor [0000.259] I> VMON: Vmon re-calibration and fine tuning done [0000.265] I> Task: UPHY init [0000.267] W> Skipping HSIO UPHY config [0000.272] W> Unsupported uphy instance 2 [0000.275] W> Unsupported uphy instance 2 [0000.280] I> GBE UPHY init done [0000.283] I> Task: Boot device init [0000.286] I> Boot_device: QSPI_FLASH instance: 0 [0000.291] I> Qspi clock source : pllc_out0 [0000.295] I> QSPI Flash: Macronix 64MB [0000.299] I> QSPI-0l initialized successfully [0000.303] I> Task: TSC init [0000.306] I> Task: Load membct [0000.309] I> RAM_CODE 0x4000421 [0000.312] I> Loading MEMBCT [0000.314] I> Slot: 0 [0000.316] I> Binary[0] block-3840 (partition size: 0x40000) [0000.322] I> Binary name: MEM-BCT-0 [0000.325] I> Size of crypto header is 8192 [0000.329] I> Size of crypto header is 8192 [0000.333] I> strt_pg_num(3840) num_of_pgs(16) read_buf(0x40050000) [0000.339] I> BCH of MEM-BCT-0 read from storage [0000.344] I> BCH address is : 0x40050000 [0000.348] I> MEM-BCT-0 header integrity check is success [0000.353] I> Binary magic in BCH component 0 is MEM0 [0000.358] I> component binary type is 0 [0000.361] I> strt_pg_num(3856) num_of_pgs(115) read_buf(0x40040000) [0000.368] I> MEM-BCT-0 binary is read from storage [0000.373] I> MEM-BCT-0 binary integrity check is success [0000.378] I> Binary MEM-BCT-0 loaded successfully at 0x40040000 (0xe580) [0000.385] I> RAM_CODE 0x4000421 [0000.390] I> RAM_CODE 0x4000421 [0000.394] I> Task: Load Page retirement list [0000.398] I> Task: SDRAM params override [0000.402] I> Task: Save mem-bct info [0000.405] I> Task: Carveout allocate [0000.409] I> RCM blob carveout will not be allocated [0000.414] I> Update CCPLEX IST carveout from MB1-BCT [0000.418] I> ECC region[0]: Start:0x0, End:0x0 [0000.423] I> ECC region[1]: Start:0x0, End:0x0 [0000.427] I> ECC region[2]: Start:0x0, End:0x0 [0000.431] I> ECC region[3]: Start:0x0, End:0x0 [0000.435] I> ECC region[4]: Start:0x0, End:0x0 [0000.440] I> Non-ECC region[0]: Start:0x80000000, End:0x280000000 [0000.446] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.450] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.455] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.460] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.470] I> allocated(CO:43) base:0x27c000000 size:0x4000000 align: 0x200000 [0000.477] I> allocated(CO:39) base:0x279e00000 size:0x2200000 align: 0x10000 [0000.484] I> allocated(CO:20) base:0x276000000 size:0x2000000 align: 0x2000000 [0000.491] I> allocated(CO:24) base:0x274000000 size:0x2000000 align: 0x2000000 [0000.498] I> allocated(CO:28) base:0x272000000 size:0x2000000 align: 0x2000000 [0000.506] I> allocated(CO:22) base:0x278000000 size:0x1000000 align: 0x1000000 [0000.513] I> allocated(CO:35) base:0x279000000 size:0xe00000 align: 0x10000 [0000.520] I> allocated(CO:02) base:0x271800000 size:0x800000 align: 0x800000 [0000.526] I> allocated(CO:03) base:0x271000000 size:0x800000 align: 0x800000 [0000.533] I> allocated(CO:06) base:0x270800000 size:0x800000 align: 0x800000 [0000.540] I> allocated(CO:56) base:0x270000000 size:0x800000 align: 0x200000 [0000.547] I> allocated(CO:07) base:0x26fc00000 size:0x400000 align: 0x400000 [0000.554] I> allocated(CO:33) base:0x26f800000 size:0x400000 align: 0x200000 [0000.561] I> allocated(CO:23) base:0x26f600000 size:0x200000 align: 0x200000 [0000.568] I> allocated(CO:01) base:0x26f500000 size:0x100000 align: 0x100000 [0000.575] I> allocated(CO:05) base:0x26f400000 size:0x100000 align: 0x100000 [0000.582] I> allocated(CO:08) base:0x26f300000 size:0x100000 align: 0x100000 [0000.589] I> allocated(CO:09) base:0x26f200000 size:0x100000 align: 0x100000 [0000.596] I> allocated(CO:15) base:0x26f100000 size:0x100000 align: 0x100000 [0000.603] I> allocated(CO:17) base:0x26f000000 size:0x100000 align: 0x100000 [0000.610] I> allocated(CO:27) base:0x26ef00000 size:0x100000 align: 0x100000 [0000.617] I> allocated(CO:42) base:0x26ee00000 size:0x100000 align: 0x100000 [0000.624] I> allocated(CO:54) base:0x26ed80000 size:0x80000 align: 0x80000 [0000.630] I> allocated(CO:34) base:0x26ed70000 size:0x10000 align: 0x10000 [0000.637] I> allocated(CO:72) base:0x26eb70000 size:0x200000 align: 0x10000 [0000.644] I> allocated(CO:47) base:0x26e600000 size:0x400000 align: 0x200000 [0000.651] I> allocated(CO:48) base:0x26eb50000 size:0x20000 align: 0x10000 [0000.658] I> allocated(CO:69) base:0x26eb30000 size:0x20000 align: 0x10000 [0000.664] I> allocated(CO:49) base:0x26eb20000 size:0x10000 align: 0x10000 [0000.671] I> allocated(CO:50) base:0x26eb10000 size:0x10000 align: 0x10000 [0000.678] I> NSDRAM base: 0x80000000, end: 0x26eb70000, size: 0x1eeb70000 [0000.685] I> Task: Thermal check [0000.688] I> max_chip_limit = 105 [0000.691] I> min_chip_limit = -28 [0000.694] I> max temp read = 67 [0000.697] I> min temp read = 66 [0000.700] I> Task: Update FSI SCR with thermal fuse data [0000.705] I> Task: Enable WDT 5th expiry [0000.709] I> Task: I2C register [0000.712] I> Task: Set I2C bus freq [0000.715] I> Task: Reset FSI [0000.718] I> Task: Pinmux init [0000.721] I> skipped mmio_addr = 0x9240008 [0000.725] I> skipped mmio_addr = 0x9240000 [0000.729] I> skipped mmio_addr = 0x9240010 [0000.733] I> skipped mmio_addr = 0x9240018 [0000.737] I> skipped mmio_addr = 0x9240020 [0000.741] I> skipped mmio_addr = 0x9240030 [0000.745] I> skipped mmio_addr = 0x9240028 [0000.749] I> skipped mmio_addr = 0x9240038 [0000.753] I> skipped mmio_addr = 0x9240040 [0000.757] I> skipped mmio_addr = 0x9240048 [0000.761] I> skipped mmio_addr = 0x9241000 [0000.765] I> skipped mmio_addr = 0x9241008 [0000.768] I> skipped mmio_addr = 0x9241010 [0000.772] I> skipped mmio_addr = 0x9241018 [0000.776] I> skipped mmio_addr = 0x9241020 [0000.780] I> skipped mmio_addr = 0x9241028 [0000.784] I> skipped mmio_addr = 0x9241030 [0000.788] I> skipped mmio_addr = 0x9241038 [0000.792] I> skipped mmio_addr = 0x9241040 [0000.796] I> skipped mmio_addr = 0x9242000 [0000.800] I> skipped mmio_addr = 0x9242008 [0000.804] I> Task: Prod config init [0000.807] I> Task: Pad voltage init [0000.811] I> Task: Prod init [0000.813] I> Task: Program rst req config reg [0000.818] I> Task: Common rail init [0000.821] I> DONE: Thermal config [0000.825] W> DEVICE_PROD: module = 13, instance = 4 not found in device prod. [0000.833] I> DONE: SOC rail config [0000.837] W> PMIC_CONFIG: Rail: MEMIO rail config not found in MB1 BCT. [0000.843] I> DONE: MEMIO rail config [0000.847] W> PMIC_CONFIG: Rail: GPU rail info not found in MB1 BCT. [0000.853] I> DONE: GPU rail info [0000.857] W> PMIC_CONFIG: Rail: CV rail info not found in MB1 BCT. [0000.863] I> DONE: CV rail info [0000.866] I> Task: Mem clock src [0000.869] I> Task: Misc. board config [0000.873] I> PMIC_CONFIG: Platform config not found in MB1 BCT. [0000.879] I> Task: SDRAM init [0000.882] I> MemoryType: 4 MemBctRevision: 1 [0000.888] I> MSS CAR: PLLM/HUB programming for MemoryType: 4 and MemBctRevision: 1 [0000.896] I> MSS CAR: Init PLLM [0000.899] I> MSS CAR: Init PLLHUB [0000.903] I> Encryption: MTS: en, TX: en, VPR: en, GSC: en [0000.915] I> SDRAM initialized! [0000.918] I> SDRAM Size in Total 0x200000000 [0000.922] I> Task: Dram Ecc scrub [0000.925] I> Task: DRAM alias check [0000.932] I> Task: Program NSDRAM carveout [0000.936] I> NSDRAM carveout encryption is enabled [0000.940] I> Program NSDRAM carveout [0000.944] I> Task: Register checker [0000.947] I> Task: Enable clock-mon [0000.951] I> FMON: Fmon re-programming done [0000.955] I> Task: Mapper init [0000.958] I> Task: SC7 Context Init [0000.962] I> Task: CCPLEX IST init [0000.965] I> Task: CPU WP0 [0000.967] I> Loading MCE [0000.970] I> Slot: 0 [0000.972] I> Binary[8] block-22784 (partition size: 0x80000) [0000.977] I> Binary name: MCE [0000.980] I> Size of crypto header is 8192 [0000.984] I> Size of crypto header is 8192 [0000.988] I> strt_pg_num(22784) num_of_pgs(16) read_buf(0x4003e000) [0000.994] I> BCH of MCE read from storage [0000.998] I> BCH address is : 0x4003e000 [0001.002] I> MCE header integrity check is success [0001.007] I> Binary magic in BCH component 0 is MTSM [0001.012] I> component binary type is 8 [0001.015] I> Size of crypto header is 8192 [0001.019] I> strt_pg_num(22800) num_of_pgs(357) read_buf(0x40000000) [0001.027] I> MCE binary is read from storage [0001.032] I> MCE binary integrity check is success [0001.037] I> Binary MCE loaded successfully at 0x40000000 (0x2c880) [0001.043] I> Size of crypto header is 8192 [0001.054] I> Size of crypto header is 8192 [0001.058] I> Sending WP0 mailbox command to PSC [0001.067] I> Task: XUSB Powergate [0001.070] I> Skipping powergate XUSB. [0001.074] I> Task: MB1 fixed firewalls [0001.080] W> Firewall readback mismatch [0001.085] I> Task: Load bpmp-fw [0001.088] I> Slot: 0 [0001.090] I> Binary[15] block-9984 (partition size: 0x180000) [0001.095] I> Binary name: BPMP_FW [0001.099] I> Size of crypto header is 8192 [0001.103] I> Size of crypto header is 8192 [0001.107] I> strt_pg_num(9984) num_of_pgs(16) read_buf(0x807fe000) [0001.113] I> BCH of BPMP_FW read from storage [0001.117] I> BCH address is : 0x807fe000 [0001.121] I> BPMP_FW header integrity check is success [0001.126] I> Binary magic in BCH component 0 is BPMF [0001.130] I> component binary type is 15 [0001.134] I> Size of crypto header is 8192 [0001.138] I> strt_pg_num(10000) num_of_pgs(1990) read_buf(0x80000000) [0001.156] I> BPMP_FW binary is read from storage [0001.162] I> BPMP_FW binary integrity check is success [0001.167] I> Binary BPMP_FW loaded successfully at 0x80000000 (0xf8bc0) [0001.174] I> Slot: 0 [0001.176] I> Binary[16] block-13056 (partition size: 0x400000) [0001.181] I> Binary name: BPMP_FW_DTB [0001.185] I> Size of crypto header is 8192 [0001.189] I> Size of crypto header is 8192 [0001.193] I> strt_pg_num(13056) num_of_pgs(16) read_buf(0x807fc000) [0001.199] I> BCH of BPMP_FW_DTB read from storage [0001.203] I> BCH address is : 0x807fc000 [0001.207] I> BPMP_FW_DTB header integrity check is success [0001.213] I> Binary magic in BCH component 0 is BPMD [0001.217] I> component binary type is 16 [0001.221] I> Size of crypto header is 8192 [0001.225] I> strt_pg_num(13072) num_of_pgs(490) read_buf(0x807bebf0) [0001.234] I> BPMP_FW_DTB binary is read from storage [0001.239] I> BPMP_FW_DTB binary integrity check is success [0001.245] I> Binary BPMP_FW_DTB loaded successfully at 0x807bebf0 (0x3d280) [0001.252] I> Task: BPMP fw ast config [0001.255] I> Task: Load psc-fw [0001.258] I> Slot: 0 [0001.260] I> Binary[17] block-21248 (partition size: 0xc0000) [0001.266] I> Binary name: PSC_FW [0001.269] I> Size of crypto header is 8192 [0001.273] I> Size of crypto header is 8192 [0001.277] I> strt_pg_num(21248) num_of_pgs(16) read_buf(0x80ffe000) [0001.283] I> BCH of PSC_FW read from storage [0001.287] I> BCH address is : 0x80ffe000 [0001.291] I> PSC_FW header integrity check is success [0001.296] I> Binary magic in BCH component 0 is PFWP [0001.300] I> component binary type is 17 [0001.304] I> Size of crypto header is 8192 [0001.308] I> strt_pg_num(21264) num_of_pgs(717) read_buf(0x80fa4600) [0001.318] I> PSC_FW binary is read from storage [0001.324] I> PSC_FW binary integrity check is success [0001.328] I> Binary PSC_FW loaded successfully at 0x80fa4600 (0x59980) [0001.335] I> Task: Load nvdec-fw [0001.338] I> Slot: 0 [0001.340] I> Binary[7] block-6400 (partition size: 0x100000) [0001.345] I> Binary name: NVDEC [0001.348] I> Size of crypto header is 8192 [0001.352] I> Size of crypto header is 8192 [0001.356] I> strt_pg_num(6400) num_of_pgs(16) read_buf(0x800fe000) [0001.363] I> BCH of NVDEC read from storage [0001.367] I> BCH address is : 0x800fe000 [0001.370] I> NVDEC header integrity check is success [0001.375] I> Binary magic in BCH component 0 is NDEC [0001.380] I> component binary type is 7 [0001.384] I> Size of crypto header is 8192 [0001.388] I> strt_pg_num(6416) num_of_pgs(560) read_buf(0x80000000) [0001.397] I> NVDEC binary is read from storage [0001.402] I> NVDEC binary integrity check is success [0001.407] I> Binary NVDEC loaded successfully at 0x80000000 (0x46000) [0001.413] I> Size of crypto header is 8192 [0001.424] I> Task: Load tsec-fw [0001.427] I> TSEC-FW load support not enabled [0001.431] I> Task: GPIO interrupt map [0001.435] I> Task: SC7 context save [0001.438] I> Slot: 0 [0001.440] I> Binary[27] block-0 (partition size: 0x100000) [0001.446] I> Binary name: BR_BCT [0001.449] I> Size of crypto header is 8192 [0001.453] I> Size of crypto header is 8192 [0001.457] I> Size of crypto header is 8192 [0001.461] I> strt_pg_num(0) num_of_pgs(16) read_buf(0xa0000000) [0001.467] I> BR_BCT binary is read from storage [0001.471] I> BR_BCT binary integrity check is success [0001.476] I> Binary BR_BCT loaded successfully at 0xa0000000 (0x2000) [0001.482] I> Slot: 0 [0001.484] I> Binary[13] block-23808 (partition size: 0x30000) [0001.490] I> Binary name: SC7-FW [0001.493] I> Size of crypto header is 8192 [0001.497] I> Size of crypto header is 8192 [0001.501] I> Size of crypto header is 8192 [0001.505] I> Size of crypto header is 8192 [0001.509] I> strt_pg_num(23808) num_of_pgs(16) read_buf(0xa0002000) [0001.515] I> BCH of SC7-FW read from storage [0001.519] I> BCH address is : 0xa0002000 [0001.523] I> SC7-FW header integrity check is success [0001.528] I> Binary magic in BCH component 0 is WB0B [0001.532] I> component binary type is 13 [0001.536] I> Size of crypto header is 8192 [0001.540] I> strt_pg_num(23824) num_of_pgs(347) read_buf(0xa0004000) [0001.548] I> SC7-FW binary is read from storage [0001.553] I> SC7-FW binary integrity check is success [0001.558] I> Binary SC7-FW loaded successfully at 0xa0004000 (0x2b440) [0001.564] I> Slot: 0 [0001.566] I> Binary[22] block-24192 (partition size: 0x30000) [0001.572] I> Binary name: PSC_RF [0001.575] I> Size of crypto header is 8192 [0001.579] I> Size of crypto header is 8192 [0001.583] I> Size of crypto header is 8192 [0001.587] I> Size of crypto header is 8192 [0001.591] I> strt_pg_num(24192) num_of_pgs(16) read_buf(0xa002f440) [0001.597] I> BCH of PSC_RF read from storage [0001.601] I> BCH address is : 0xa002f440 [0001.605] I> PSC_RF header integrity check is success [0001.610] I> Binary magic in BCH component 0 is PSCR [0001.615] I> component binary type is 22 [0001.618] I> Size of crypto header is 8192 [0001.622] I> strt_pg_num(24208) num_of_pgs(224) read_buf(0xa0031440) [0001.630] I> PSC_RF binary is read from storage [0001.635] I> PSC_RF binary integrity check is success [0001.639] I> Binary PSC_RF loaded successfully at 0xa0031440 (0x1be60) [0001.649] I> Task: Save WP0 payload to SC7 ctx [0001.653] I> Task: Load MB2rf binary to SC7 ctx [0001.657] I> Slot: 0 [0001.659] I> Binary[14] block-24576 (partition size: 0x20000) [0001.665] I> Binary name: MB2_RF [0001.668] I> Size of crypto header is 8192 [0001.672] I> Size of crypto header is 8192 [0001.676] I> Size of crypto header is 8192 [0001.680] I> Size of crypto header is 8192 [0001.684] I> strt_pg_num(24576) num_of_pgs(16) read_buf(0xa00d6aa0) [0001.690] I> BCH of MB2_RF read from storage [0001.694] I> BCH address is : 0xa00d6aa0 [0001.698] I> MB2_RF header integrity check is success [0001.703] I> Binary magic in BCH component 0 is MB2R [0001.708] I> component binary type is 14 [0001.712] I> Size of crypto header is 8192 [0001.715] I> strt_pg_num(24592) num_of_pgs(224) read_buf(0xa00d8aa0) [0001.723] I> MB2_RF binary is read from storage [0001.728] I> MB2_RF binary integrity check is success [0001.732] I> Binary MB2_RF loaded successfully at 0xa00d8aa0 (0x1bfc0) [0001.739] I> Task: Save fuse alias data to SC7 ctx [0001.744] I> Task: Save PMIC data to SC7 ctx [0001.748] I> Task: Save Pinmux data to SC7 ctx [0001.752] I> Task: Save Pad Voltage data to SC7 ctx [0001.757] I> Task: Save controller prod data to SC7 ctx [0001.762] I> Task: Save prod cfg data to SC7 ctx [0001.766] I> Task: Save I2C bus freq data to SC7 ctx [0001.771] I> Task: Save SOCTherm data to SC7 ctx [0001.775] I> Task: Save FMON data to SC7 ctx [0001.780] I> Task: Save VMON data to SC7 ctx [0001.784] I> Task: Save TZDRAM data to SC7 ctx [0001.788] I> Task: Save GPIO int data to SC7 ctx [0001.792] I> Task: Save clock data to SC7 ctx [0001.797] I> Task: Save debug data to SC7 ctx [0001.801] I> Task: Save MBWT data to SC7 ctx [0001.809] I> SC7 context save done [0001.812] I> Task: Load MB2/Applet/FSKP [0001.816] I> Loading MB2 [0001.818] I> Slot: 0 [0001.820] I> Binary[6] block-8448 (partition size: 0x80000) [0001.826] I> Binary name: MB2 [0001.828] I> Size of crypto header is 8192 [0001.832] I> Size of crypto header is 8192 [0001.836] I> strt_pg_num(8448) num_of_pgs(16) read_buf(0x8007e000) [0001.842] I> BCH of MB2 read from storage [0001.846] I> BCH address is : 0x8007e000 [0001.850] I> MB2 header integrity check is success [0001.855] I> Binary magic in BCH component 0 is MB2B [0001.860] I> component binary type is 6 [0001.863] I> Size of crypto header is 8192 [0001.867] I> strt_pg_num(8464) num_of_pgs(838) read_buf(0x80000000) [0001.878] I> MB2 binary is read from storage [0001.883] I> MB2 binary integrity check is success [0001.888] I> Binary MB2 loaded successfully at 0x80000000 (0x68b10) [0001.894] I> Task: Map CCPLEX SHARED carveout [0001.898] I> Task: Prepare MB2 params [0001.902] I> Task: Dram ecc test [0001.905] I> Task: Misc NV security settings [0001.909] I> NVDEC sticky bits programming done [0001.913] I> Successfully powergated NVDEC [0001.917] I> Task: Disable/Reload WDT [0001.921] I> Task: Program misc carveouts [0001.925] I> Program IPC carveouts [0001.928] I> Task: Disable SCPM/POD reset [0001.932] I> SLCG Global override status := 0x0 [0001.937] I> MB1: MSS reconfig completed I> MB2 (version: 0.0.0.0-t234-54845784-934581f8) I> t234-A01-0-Silicon (0x12347) I> Boot-mode : Coldboot I> Emulation: I> Entry timestamp: 0x001dfb73 I> Regular heap: [base:0x40040000, size:0x10000] I> DMA heap: [base:0x270000000, size:0x800000] I> Task: ARI update carveout TZDRAM (0x50002050) I> Task: Check MC errors (0x5000204c) I> Task: Enable hot-plug capability (0x500290f8) I> Task: TZDRAM heap init (0x5001a0fc) I> Task: PSC mailbox init (0x50018864) I> Task: Crypto init (0x50006874) I> Task: Enable GP-SE clock (0x500021b4) I> Task: Measured Boot init (0x5001c04c) I> Task: fTPM silicon identity init (0x5001c1f8) I> fTPM is not enabled. I> Task: OEM SC7 context save init (0x5001b598) I> Task: I2C register (0x50002010) I> Task: Map CCPLEX_INTERWORLD_SHMEM carveout (0x50001ff8) I> Task: Program CBB PCIE AMAP regions (0x5001bcf8) I> Task: Boot device init (0x50001f40) I> Boot_device: QSPI_FLASH instance: 0 I> Qspi clock source : pllc_out0 I> QSPI-0l initialized successfully I> Task: Partition Manager Init (0x50001f20) I> Active chain: 0 I> Found 57 partitions in QSPI_FLASH (instance 0) I> Task: Load and authenticate registered FWs (0x5001f064) I> Task: Load AUXP FWs (0x50028c7c) I> Successfully register SPE FW load task with MB2 loader I> Skipping SCE FW load I> Successfully register RCE FW load task with MB2 loader I> Successfully register DCE FW load task with MB2 loader I> Unpowergating APE I> Unpowergate done I> Successfully register APE FW load task with MB2 loader I> Skipping FSI FW load I> Successfully register XUSB FW load task with MB2 loader I> Active chain: 0 I> Partition name: A_spe-fw I> Size of partition: 589824 I> Binary@ device:3/0 block-55040 (partition size: 0x90000), name: A_spe-fw I> Active chain: 0 I> Partition name: A_rce-fw I> Size of partition: 1048576 I> Binary@ device:3/0 block-56192 (partition size: 0x100000), name: A_rce-fw I> spe: Authentication Finalize Done I> Binary spe loaded successfully at 0x26f300000 I> Active chain: 0 I> Partition name: A_dce-fw I> Size of partition: 5242880 I> Binary@ device:3/0 block-44800 (partition size: 0x500000), name: A_dce-fw I> rce: Authentication Finalize Done I> Binary rce loaded successfully at 0x26f000000 I> Successfully register RCE FW context save task with MB2 loader I> dce : oem authentication of header done I> dce : meta-blob integrity check is success. I> dce : will be decompressed at 0x276000000 I> version 1 Bin 1 BCheckSum 0 content_size 0 Content ChkSum 1 reserved_00 0 I> Reserved10 0 BlockMaxSize 5 Reserved11 0 I> dce : decompressed to 9457792 bytes I> dce: plain binary integrity check is success I> Active chain: 0 I> Partition name: A_adsp-fw I> Size of partition: 2097152 I> Binary@ device:3/0 block-58240 (partition size: 0x200000), name: A_adsp-fw I> dce: Authentication Finalize Done I> Binary dce loaded successfully at 0x276000000 I> Active chain: 0 I> Partition name: A_xusb-fw I> Size of partition: 262144 I> Binary@ device:3/0 block-9472 (partition size: 0x40000), name: A_xusb-fw I> ape: Authentication Finalize Done I> Binary ape loaded successfully at 0x26fc00000 I> Successfully register APE FW context save task with MB2 loader I> xusb: Authentication Finalize Done I> Binary xusb loaded successfully at 0x26f400000 I> Successfully register XUSB FW context save task with MB2 loader I> Task: Check MC errors (0x5000204c) I> Task: Carveout setup (0x500217e4) I> Program remaining OEM carveouts I> Task: Enable FSITHERM (0x50018738) I> Task: Enable FSI VMON (0x50018234) I> Task: Validate FSI Therm readings (0x50018318) I> Task: Restore XUSB sec (0x50001ef4) I> Task: Enable FSI SE clock (0x50018cc0) I> Task: Initialize SBSA UART CAR (0x50002118) I> Task: Initialize CPUBL Params (0x50019cac) I> CPUBL-params @ 0x272000000 I> Task: Ratchet update (0x5002a194) W> Skip ratchet update - OPTIN fuse not set I> Task: Prepare eeprom data (0x50019a78) I> Task: Revoke PKC fuse (0x50001d40) I> PKC revoke fuse burn not requested I> Task: FSI padctl context save (0x5001b874) W> Skipping FSI padctl config save: fsi not enabled I> Task: Unpowergate APE (0x50019428) W> mb2_unpowergate_ape: skip! APE is in unpowergated state I> Task: OEM firewalls (0x50025cf0) I> OEM firewalls configured I> Task: Powergate APE (0x5001959c) I> Powergating APE I> Powergate done I> Task: OEM firewall restore saved settings (0x50026144) I> Task: Unhalt AUXPs (0x50028f00) I> Unhalting SPE.. I> Enabling combined UART spe: early_init vic initialized tsc initialized aon lic initialized spe: tag is 5243985d1b1eb3f06fac6d36bd7e74ac spe: SafeRTOS v8.4 spe: init scheduler initialized aon hsp initialized tag initialized tcu initialized bpmp ipc initialized spe: late init cpu_nic clock initialized apb clock initialized pm initialized bpmp hsp initialized top1 hsp initialized ccplex ipc initialized spe: start scheduler I> Task: Trigger mailbox for PSC-BL1 exit (0x500188e4) I> Sending opcode 0x4d420802 to psc INFO: Entering psc_monitor_init! INFO: GSC22 BOM:0x278002000 SIZE:0x1000000 CLIENT_ACCESS1:00180000 INFO: PSCFW BUILD VERSION: 8a33b23-73b589c-8a15f76-rel-t234 INFO: mstatus:0xa00000808 INFO: Supervisor entry_point:c108c00 I> Received ACK from psc I> TasINFO: MONITOR: user task addr:0x278022000, blob offset:0x00020000 INFO: MONITOR: populated user images:13 INFO: mret to Supervisor! INFO: psc supervisor init. INFO: psc_irq_init... INFO: enter idle task. hwwdt_init: WDT boot cfg 0x710010 sts 0x10 bpmp: socket 0 bpmp: base binary md5 is fcc6f4f897ab64a32c3de470c48f0036 bpmp: combined binary md5 is a5fd653d3815177549cc44e087b1bd9e bpmp: firmware tag is a5fd653d3815177549cc-fcc6f4f897a Control register check for CBB_CENTRAL_CBB_FIREWALL_MCB_BLF failed, expected value: 80030000 != actual value: 00000000 address: 13a159d0 Write control check for CBB_CENTRAL_CBB_FIREWALL_MCB_BLF failed, expected value: 0f18000b != actual value: 00000000 address: 13a159c8 Control register check for CBB_CENTRAL_CBB_FIREWALL_MCB_BLF failed, expected value: 80030000 != actual value: 00000000 address: 13a159d0 Write control check for CBB_CENTRAL_CBB_FIREWALL_PWM7_BLF failed, expected value: 00100008 != actual value: 0010000a address: 13a178a8 initialized vwdt initialized mail_early initialized fuse initialized vfrel initialized adc fmon_populate_monitors: found 199 monitors initialized fmon initialized mc initialized reset initialized uphy_early initialized emc_early initialized pm 465 clocks registered initialized clk_mach initialized clk_cal_early initialized clk_mach_early_config initialized io_dpd initialized soctherm initialized regime initialized i2c vrmon_dt_init: vrmon node not found vrmon_chk_boot_state: found 0 rail monitors initialized vrmon initialized regulator initialized avfs_clk_platform initialized powergate k: Start initialized dvs initialized clk_mach_config suspend progress: 0x80000000 initialized suspend initialized strap initialized mce_dbell secure NOR provision (0x5001bb10) I> Task: Load FSI keyblob (0x50018d08) I> Task: Unhalt AUXPs (0x50028f08) I> SCE unhalt skipped I> Unhalting RCE I> RCE unhalt successful I> DCE unhalt successful I> APE unhalt skipped I> FSI unhalt skipped I> Task: Load CPUBL (0x50019dd0) I> Task: Load TOS (0x5001a560) I> Tasinitialized emc initialized emc_mrq [ 2.428747] Camera-FW on t234-rce-safe started initialized clk_cal initialized uphy_dt initialized uphy_mrq GBE UPHY reset hTCU early console enabled. as been de-asserted 0x0 initialized uphy initialized pg_late initialized pg_mrq_init swdtimer_init: reg polling start w period 47 ms initialized swdtimer initialized hwwdt_late initialized bwmgr initialized thermal_host_trip initialized thermal_mrq initialized oc_mrq initialized reset_mrq initialized mail_mrq initialized fmon_mrq initialized clk_mrq initialized avfs_mrq initialized i2c_mrq initialized tag_mrq initialized bwmgr_mrq initialized console_mrq missing prod DT calibration data for 199 fmons initialized clk_sync_fmon_post k: Load and authenticate registered FWs (0initialized clk_cal_late initialized noc_late initialized cvc x5001f064) I> Active chain: 0 initialized avfs_clk_mach_post initialized avfs_clk_platform_post initialized cvc_late WARNING @ [platform/drivers/rm/rm.c]: shared rails 0/2 have not matching zones 0/1 WARNING @ [platform/drivers/rm/rm.c]: shared rails 0/3 have not matching zone list sizes 1/3 WARNING @ [platform/drivers/rm/rm.c]: shared rails 0/3 have not matching zones 0/2 WARNING @ [platform/drivers/rm/rm.c]: shared rails 2/0 have not matching zones 1/0 WARNING @ [platform/drivers/rm/rm.c]: shared rails 2/3 have not matching zone list sizes 1/3 WARNING @ [platform/drivers/rm/rm.c]: shared rails 2/3 have not matching zones 1/2 WARNING @ [platform/drivers/rm/rm.c]: shared rails 3/0 have not matching zone list sizes 3/1 WARNING @ [platform/drivers/rm/rm.c]: shared rails 3/0 have not matching zones 2/0 WARNING @ [platform/drivers/rm/rm.c]: shared rails 3/2 have not matching zone list sizes 3/1 WARNING @ [platform/drivers/rm/rm.c]: shared rails 3/2 have not matching zones 2/1 initialized rm initialized console_late handling unreferenced clks enable can1_core enable can1_host enable can2_core enable can2_host enable pwm3 enable sdmmc4_axicif enable mss_encrypt enable maud enable pllg_ref enable dsi_core enable aza_2xbit enable xusb_ss enable xusb_fs enable xusb_falcon enable xusb_core_mux enable dsi_lp initialized clk_mach_post initialized pg_post initialized regulator_post initialized profile initialized mrq initialized patrol_scrubber initialized cactmon initialized extras_post bpmp: init complete [ 2.604850] Camera-FW on t234-rce-safe ready SHA1=55ecd57d (crt 14.074 ms, total boot 191.239 ms) DCE: FW Boot Done I> Partition name: A_cpu-bootloader I> Size of partition: 3670016 I> Binary@ device:3/0 block-24832 (partition size: 0x380000), name: A_cpu-bootloader I> cpubl : oem authentication of header done I> cpubl : meta-blob integrity check is success. I> cpubl : will be decompressed at 0x26e600000 I> version 1 Bin 1 BCheckSum 0 content_size 0 Content ChkSum 1 reserved_00 0 I> Reserved10 0 BlockMaxSize 5 Reserved11 0 I> cpubl : decompressed to 3186816 bytes I> cpubl: plain binary integrity check is success I> Active chain: 0 I> Partition name: A_secure-os I> Size of partition: 4194304 I> Binary@ device:3/0 block-32000 (partition size: 0x400000), name: A_secure-os I> MB2-params @ 0x40060000 I> cpubl_params: nsdram: carveout: 1, encryption: 1 I> NSDRAM carveout base: 0x80000000, size: 0x1eeb70000 I> cpubl: Authentication Finalize Done I> Binary cpubl loaded successfully at 0x26e600000 I> tos: Authentication Finalize Done I> Binary tos loaded successfully at 0x27fdc7000 I> Relocating OP-TEE dtb from: 0x27fefec50 to 0x27c000860, size: 0x2886 I> [0] START: 0x80000000, SIZE: 0x1eeb70000 I> [1] START: 0x272000000, SIZE: 0x2000000 I> Setting NS memory ranges to OP-TEE dtb finished. I> Active chain: 0 I> Partition name: A_eks I> Size of partition: 262144 I> Binary@ device:3/0 block-44288 (partition size: 0x40000), name: A_eks I> eks: Authentication Finalize Done I> Binary eks loaded successfully at 0x270000200 I> EKB detected (length: 0x410) @ VA:0x270000200 I> Task: Prepare TOS params (0x5001a4d8) I> Setting EKB blob info to OPTEE dtb finished. I> Setting OPTEE arg3: 0x27c000860 I> Task: OEM SC7 context save (0x5001b970) I> OEM sc7 context saved I> Task: Disable MSS perf stats (0x50028f94) I> Task: Program display sticky bits (0x50028f10) I> Task: Storage device deinit (0x500020bc) I> Task: SMMU external bypass disable (0x50018848) I> Task: SMMU init (0x50018764) I> Task: Program GICv3 registers (0x50029034) I> Task: Audit firewall settings (0x50025f44) I> Task: Bootchain failure check (0x500025c8) I> Current Boot-Chain Slot: 0 I> BR-BCT Boot-Chain is 0, and status is 1. Set UPDATE_BRBCT bit to 0 I> MB2 finished NOTICE: BL31: v2.6(release):jetson_35.5 NOTICE: BL31: Built : 11:10:12, Apr 9 2024 I/TC: Physical secure memory base 0x27c040000 size 0x3fc0000 I/TC: I/TC: Non-secure external DT found I/TC: OP-TEE version: 3.22 (gcc version 9.3.0 (Buildroot 2020.08)) #2 Tue Apr 9 03:33:30 UTC 2024 aarch64 I/TC: WARNING: This OP-TEE configuration might be insecure! I/TC: WARNING: Please check https://optee.readthedocs.io/en/latest/architecture/porting_guidelines.html I/TC: Primary CPU initializing I/TC: Test OEM keys are being used. This is insecure for shipping products! I/TC: Primary CPU switching to normal world boot Jetson UEFI firmware (version 5.0-35550185 built on 2024-02-20T04:21:22+00:00) I/TC: Reserved shared memory is disabled I/TC: Dynamic shared memory is enabled I/TC: Normal World virtualization support is disabled I/TC: Asynchronous notifications are disabled Jetson UEFI firmware (version 5.0-35550185 built on 2024-02-20T04:21:22+00:00) ESC to enter Setup. F11 to enter Boot Manager Menu. Enter to continue boot. ** WARNING: Test Key is used. ** L4TLauncher: Attempting Direct Boot EFI stub: Booting Linux Kernel... EFI stub: Using DTB from configuration table EFI stub: Loaded initrd from LINUX_EFI_INITRD_MEDIA_GUID device path EFI stub: Exiting boot services and installing virtual address map... I/TC: Secondary CPU 1 initializing I/TC: Secondary CPU 1 switching to normal world boot I/TC: Secondary CPU 2 initializing I/TC: Secondary CPU 2 switching to normal world boot I/TC: Secondary CPU 3 initializing I/TC: Secondary CPU 3 switching to normal world boot I/TC: Secondary CPU 6 initializing I/TC: Secondary CPU 6 switching to normal world boot I/TC: Secondary CPU 7 initializing I/TC: Secondary CPU 7 switching to normal world boot [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd421] [ 0.000000] Linux version 5.10.192-tegra (kenexs@kenexs-arch) (aarch64-buildroot-linux-gnu-gcc.br_real (Buildroot 2020.08) 9.3.0, GNU ld (GNU Binutils) 2.33.1) #162 SMP PREEMPT Thu Jul 4 15:50:00 CST 2024 [ 0.000000] OF: fdt: memory scan node memory@80000000, reg size 16, [ 0.000000] OF: fdt: - 80000000 , c0000000 [ 0.000000] Machine model: KENEXS V700 V01 Board [ 0.000000] efi: EFI v2.70 by EDK II [ 0.000000] efi: RTPROP=0x2661afd98 SMBIOS=0xffff0000 SMBIOS 3.0=0x26a1b0000 MEMATTR=0x264979018 ESRT=0x26497ae98 RNG=0x258480018 MEMRESERVE=0x258df0c18 [ 0.000000] random: crng init done [ 0.000000] esrt: Reserving ESRT space from 0x000000026497ae98 to 0x000000026497aed0. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000248000000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x0000000273ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fffdffff] [ 0.000000] node 0: [mem 0x00000000fffe0000-0x00000000ffffffff] [ 0.000000] node 0: [mem 0x0000000100000000-0x000000025af90fff] [ 0.000000] node 0: [mem 0x000000025af91000-0x000000025b31bfff] [ 0.000000] node 0: [mem 0x000000025b31c000-0x00000002687fffff] [ 0.000000] node 0: [mem 0x0000000268800000-0x000000026a73ffff] [ 0.000000] node 0: [mem 0x000000026a740000-0x000000026eb0ffff] [ 0.000000] node 0: [mem 0x000000026eb10000-0x000000026eb1ffff] [ 0.000000] node 0: [mem 0x0000000272000000-0x0000000273ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x0000000273ffffff] [ 0.000000] On node 0, zone Normal: 224 pages in unavailable ranges [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 32 pages/cpu s90392 r8192 d32488 u131072 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Virtualization Host Extensions [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] alternatives: patching kernel code [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2002464 [ 0.000000] Kernel command line: root=PARTUUID=6efa5acd-5d4c-4a28-92b7-fd3e6762f352 rw rootwait rootfstype=ext4 mminit_loglevel=4 console=ttyTCU0,115200 console=ttyAMA0,115200 firmware_class.path=/etc/firmware fbcon=map:0 net.ifnames=0 [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000effe0000-0x00000000fffe0000] (256MB) [ 0.000000] Memory: 7353348K/8137856K available (18496K kernel code, 3168K rwdata, 7164K rodata, 3968K init, 1417K bss, 522364K reserved, 262144K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 960 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000f440000 [ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:608, num:70) [ 0.000000] GICv2m: range[mem 0x0f410000-0x0f41ffff], SPI[608:677] [ 0.000000] arch_timer: cp15 timer(s) running at 31.25MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xe6a171046, max_idle_ns: 881590405314 ns [ 0.000002] sched_clock: 56 bits at 31MHz, resolution 32ns, wraps every 4398046511088ns [ 0.000699] Console: colour dummy device 80x25 [ 0.000742] Calibrating delay loop (skipped), value calculated using timer frequency.. 62.50 BogoMIPS (lpj=125000) [ 0.000750] pid_max: default: 32768 minimum: 301 [ 0.000802] LSM: Security Framework initializing [ 0.000825] Yama: becoming mindful. [ 0.000842] SELinux: Initializing. [ 0.000900] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.000913] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.001959] rcu: Hierarchical SRCU implementation. [ 0.002036] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.002516] DTS File Name: /home/kenexs/data/images/jetson/r35.5.0/Linux_for_Tegra/sources/kernel/kernel-5.10/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t23x/p3768/kernel-dts/tegra234-p3767-0001-p3768-0000-a0.dts [ 0.002520] DTB Build time: Jul 9 2024 16:23:39 [ 0.003804] Tegra Revision: A01 SKU: 0xd4 CPU Process: 0 SoC Process: 0 [ 0.004038] Remapping and enabling EFI services. [ 0.004870] smp: Bringing up secondary CPUs ... [ 0.033568] Detected PIPT I-cache on CPU1 [ 0.033607] GICv3: CPU1: found redistributor 100 region 0:0x000000000f460000 [ 0.033642] CPU1: Booted secondary processor 0x0000000100 [0x410fd421] [ 0.062294] Detected PIPT I-cache on CPU2 [ 0.062307] GICv3: CPU2: found redistributor 200 region 0:0x000000000f480000 [ 0.062322] CPU2: Booted secondary processor 0x0000000200 [0x410fd421] [ 0.090925] Detected PIPT I-cache on CPU3 [ 0.090934] GICv3: CPU3: found redistributor 300 region 0:0x000000000f4a0000 [ 0.090948] CPU3: Booted secondary processor 0x0000000300 [0x410fd421] [ 0.121584] Detected PIPT I-cache on CPU4 [ 0.121606] GICv3: CPU4: found redistributor 10200 region 0:0x000000000f500000 [ 0.121632] CPU4: Booted secondary processor 0x0000010200 [0x410fd421] [ 0.150293] Detected PIPT I-cache on CPU5 [ 0.150303] GICv3: CPU5: found redistributor 10300 region 0:0x000000000f520000 [ 0.150317] CPU5: Booted secondary processor 0x0000010300 [0x410fd421] [ 0.150378] smp: Brought up 1 node, 6 CPUs [ 0.150389] SMP: Total of 6 processors activated. [ 0.150393] CPU features: detected: Privileged Access Never [ 0.150394] CPU features: detected: LSE atomic instructions [ 0.150396] CPU features: detected: User Access Override [ 0.150397] CPU features: detected: 32-bit EL0 Support [ 0.150400] CPU features: detected: Common not Private translations [ 0.150401] CPU features: detected: RAS Extension Support [ 0.150402] CPU features: detected: Data cache clean to the PoU not required for I/D coherence [ 0.150404] CPU features: detected: CRC32 instructions [ 0.150406] CPU features: detected: Speculative Store Bypassing Safe (SSBS) [ 0.167543] spectre-bhb mitigation disabled by command line option [ 0.183015] CPU: All CPU(s) started at EL2 [ 0.184695] devtmpfs: initialized [ 0.199870] Registered cp15_barrier emulation handler [ 0.199877] Registered setend emulation handler [ 0.199883] KASLR enabled [ 0.199998] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.200009] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.201508] pinctrl core: initialized pinctrl subsystem [ 0.202188] NET: Registered protocol family 16 [ 0.202889] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations [ 0.202948] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.203002] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.203029] audit: initializing netlink subsys (disabled) [ 0.203094] audit: type=2000 audit(0.200:1): state=initialized audit_enabled=0 res=1 [ 0.203312] thermal_sys: Registered thermal governor 'step_wise' [ 0.203314] thermal_sys: Registered thermal governor 'power_allocator' [ 0.203317] thermal_sys: Registered thermal governor 'pid_thermal_gov' [ 0.204091] cpuidle: using governor menu [ 0.204202] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.204262] ASID allocator initialised with 32768 entries [ 0.204345] Serial: AMBA PL011 UART driver [ 0.206104] tegra234_mc_sid_probe(): tegra234 mc-sid probe successful [ 0.206126] Tegra reboot handler registered. [ 0.224673] mc: mapped MMIO address: 0xffff8000107b0000 -> 0x2c10000 [ 0.224684] mc: mapped MMIO address: 0xffff8000107d0000 -> 0x2c20000 [ 0.224689] mc: mapped MMIO address: 0xffff8000107f0000 -> 0x2c30000 [ 0.224697] mc: mapped MMIO address: 0xffff800010810000 -> 0x2c40000 [ 0.224702] mc: mapped MMIO address: 0xffff800010830000 -> 0x2c50000 [ 0.224708] mc: mapped MMIO address: 0xffff800010850000 -> 0x2b80000 [ 0.224714] mc: mapped MMIO address: 0xffff800010870000 -> 0x2b90000 [ 0.224719] mc: mapped MMIO address: 0xffff800010890000 -> 0x2ba0000 [ 0.224724] mc: mapped MMIO address: 0xffff8000108b0000 -> 0x2bb0000 [ 0.224730] mc: mapped MMIO address: 0xffff8000108d0000 -> 0x1700000 [ 0.224735] mc: mapped MMIO address: 0xffff8000108f0000 -> 0x1710000 [ 0.224740] mc: mapped MMIO address: 0xffff800010910000 -> 0x1720000 [ 0.224745] mc: mapped MMIO address: 0xffff800010930000 -> 0x1730000 [ 0.224750] mc: mapped MMIO address: 0xffff800010950000 -> 0x1740000 [ 0.224755] mc: mapped MMIO address: 0xffff800010970000 -> 0x1750000 [ 0.224759] mc: mapped MMIO address: 0xffff800010990000 -> 0x1760000 [ 0.224764] mc: mapped MMIO address: 0xffff8000109b0000 -> 0x1770000 [ 0.224772] nv-tegra-mc 2c10000.mc: No mssnvlink node [ 0.224795] mc-err: mcerr ops are set to t23x [ 0.225523] 31d0000.serial: ttyAMA0 at MMIO 0x31d0000 (irq = 67, base_baud = 0) is a SBSA [ 1.190950] printk: console [ttyAMA0] enabled [ 1.199244] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 1.205953] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 1.212653] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 1.219350] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 1.227520] ACPI: Interpreter disabled. [ 1.231800] ddr-vddq: supplied by vdd-5v [ 1.235868] ddr-vdd2: supplied by vdd-5v [ 1.239893] vdd-AO-1v2: supplied by vdd-5v [ 1.244104] vdd-3v3: supplied by vdd-5v [ 1.248064] vdd-rtc: supplied by vdd-AO-1v2 [ 1.252355] vdd-0v95-uphy: supplied by vdd-AO-1v2 [ 1.257157] vdd-0v95-hdmi: supplied by vdd-AO-1v2 [ 1.262089] vdd-1v8: supplied by vdd-3v3-sys [ 1.266455] vdd-3v3-AO: supplied by vdd-5v-sys [ 1.270991] vdd-av10-hub: supplied by vdd-5v-sys [ 1.275721] vdd-vbus-a: supplied by vdd-5v-sys [ 1.280257] vdd-vbus-b: supplied by vdd-5v-sys [ 1.284808] vdd-3v3-dp: supplied by vdd-3v3-sys [ 1.289507] vdd_12v: supplied by vcc_24 [ 1.293443] vdd_5v_in: supplied by vcc_24 [ 1.297613] vdd_3v3_sys: supplied by vdd_5v_in [ 1.302158] vga_vin5v: supplied by vdd_5v_in [ 1.306550] vdd33: supplied by vdd_3v3_sys [ 1.310737] vdd_1v8: supplied by vdd_3v3_sys [ 1.315106] vga_dvdd33: supplied by vdd_3v3_sys [ 1.319741] rtl_vdd33_6: supplied by vdd_3v3_sys [ 1.324447] vdd33_d_6: supplied by vdd_3v3_sys [ 1.328982] rtl_vdd33_7: supplied by vdd_3v3_sys [ 1.333709] vdd33_d_7: supplied by vdd_3v3_sys [ 1.338246] p3v3: supplied by vdd_3v3_sys [ 1.342372] vga_dvdd12: supplied by vga_vin5v [ 1.346831] hdmi_hdp_vga: supplied by vga_vin5v [ 1.351668] iommu: Default domain type: Translated [ 1.356579] eventlib_kernel: keventlib is initialized, test id: 0 [ 1.362844] SCSI subsystem initialized [ 1.366663] usbcore: registered new interface driver usbfs [ 1.372160] usbcore: registered new interface driver hub [ 1.377478] usbcore: registered new device driver usb [ 1.382726] mc: Linux media interface: v0.10 [ 1.387001] videodev: Linux video capture interface: v2.00 [ 1.392641] pps_core: LinuxPPS API ver. 1 registered [ 1.397602] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.406735] PTP clock support registered [ 1.410884] tegra_wdt_t18x 2190000.watchdog: Tegra WDT init timeout = 120 sec [ 1.418052] tegra_wdt_t18x 2190000.watchdog: Registered successfully [ 1.425712] Registered efivars operations [ 1.430244] FPGA manager framework [ 1.433668] Advanced Linux Sound Architecture Driver Initialized. [ 1.440040] Bluetooth: Core ver 2.22 [ 1.443621] NET: Registered protocol family 31 [ 1.448061] Bluetooth: HCI device and connection manager initialized [ 1.454415] Bluetooth: HCI socket layer initialized [ 1.459290] Bluetooth: L2CAP socket layer initialized [ 1.464346] Bluetooth: SCO socket layer initialized [ 1.469744] camchar: rtcpu character device driver loaded [ 1.475376] clocksource: Switched to clocksource arch_sys_counter [ 1.649806] VFS: Disk quotas dquot_6.6.0 [ 1.653769] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.661195] pnp: PnP ACPI: disabled [ 1.666550] la/ptsa driver initialized. [ 1.670447] NET: Registered protocol family 2 [ 1.674933] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 1.683740] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 1.692287] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 1.700261] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) [ 1.708171] TCP: Hash tables configured (established 65536 bind 65536) [ 1.714769] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 1.721574] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 1.728876] NET: Registered protocol family 1 [ 1.733406] RPC: Registered named UNIX socket transport module. [ 1.739329] RPC: Registered udp transport module. [ 1.744038] RPC: Registered tcp transport module. [ 1.748739] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.755182] PCI: CLS 0 bytes, default 64 [ 1.759213] Trying to unpack rootfs image as initramfs... [ 1.894343] Freeing initrd memory: 9548K [ 1.900441] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.908451] kvm [1]: IPA Size Limit: 48 bits [ 1.912746] kvm [1]: GICv3: no GICV resource entry [ 1.917535] kvm [1]: disabling GICv2 emulation [ 1.921999] kvm [1]: GIC system register CPU interface enabled [ 1.927893] kvm [1]: vgic interrupt IRQ9 [ 1.931913] kvm [1]: VHE mode initialized successfully [ 1.937733] Initialise system trusted keyrings [ 1.942277] workingset: timestamp_bits=46 max_order=21 bucket_order=0 [ 1.950877] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.957001] NFS: Registering the id_resolver key type [ 1.962065] Key type id_resolver registered [ 1.966245] Key type id_legacy registered [ 1.970288] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.976995] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.984400] ntfs: driver 2.1.32 [Flags: R/W]. [ 2.000678] NET: Registered protocol family 38 [ 2.005124] Key type asymmetric registered [ 2.009218] Asymmetric key parser 'x509' registered [ 2.014111] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 239) [ 2.021556] io scheduler mq-deadline registered [ 2.026087] io scheduler kyber registered [ 2.033998] tegra-pwm 3280000.pwm: PWM clk can sleep in ops [ 2.039600] tegra-pwm 32a0000.pwm: PWM clk can sleep in ops [ 2.045184] tegra-pwm 32c0000.pwm: PWM clk can sleep in ops [ 2.050767] tegra-pwm 32e0000.pwm: PWM clk can sleep in ops [ 2.057186] efifb: probing for efifb [ 2.060793] efifb: framebuffer at 0x279e00000, using 8640k, total 8640k [ 2.067405] efifb: mode is 1920x1080x32, linelength=8192, pages=1 [ 2.073496] efifb: scrolling: redraw [ 2.077066] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0 [ 2.085648] Console: switching to colour frame buffer device 240x67 [ 2.094675] fb0: EFI VGA frame buffer device [ 2.100783] tegra_dc_assign_hw_data: no matching compatible node [ 2.106791] tegradccommon module_init failed [ 2.111058] tegradc module_init failed [ 2.115074] EINJ: ACPI disabled. [ 2.119991] tegra-pmc c360000.pmc: scratch reg offset dts data not present [ 2.126870] tegra-pmc: ### PMC reset source: MAINSWRST [ 2.132006] tegra-pmc: ### PMC reset level: L1 [ 2.136445] tegra-pmc: ### PMC reset status reg: 0x2d [ 2.142886] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 3.642823] printk: console [ttyTCU0] enabled [ 3.647873] arm-smmu 12000000.iommu: probing hardware configuration... [ 3.654574] arm-smmu 12000000.iommu: SMMUv2 with: [ 3.659407] arm-smmu 12000000.iommu: stage 1 translation [ 3.664969] arm-smmu 12000000.iommu: stage 2 translation [ 3.670521] arm-smmu 12000000.iommu: nested translation [ 3.675984] arm-smmu 12000000.iommu: stream matching with 128 register groups [ 3.683398] arm-smmu 12000000.iommu: 128 context banks (0 stage-2 only) [ 3.692278] arm-smmu 12000000.iommu: Supported page sizes: 0x00001000 [ 3.698971] arm-smmu 12000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 3.705664] arm-smmu 12000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 3.713180] arm-smmu 10000000.iommu: probing hardware configuration... [ 3.719879] arm-smmu 10000000.iommu: SMMUv2 with: [ 3.724707] arm-smmu 10000000.iommu: stage 1 translation [ 3.730248] arm-smmu 10000000.iommu: stage 2 translation [ 3.735791] arm-smmu 10000000.iommu: nested translation [ 3.741249] arm-smmu 10000000.iommu: stream matching with 128 register groups [ 3.748663] arm-smmu 10000000.iommu: 128 context banks (0 stage-2 only) [ 3.757513] arm-smmu 10000000.iommu: Supported page sizes: 0x00001000 [ 3.764213] arm-smmu 10000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 3.770897] arm-smmu 10000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 3.778033] arm-smmu 8000000.iommu: probing hardware configuration... [ 3.784653] arm-smmu 8000000.iommu: SMMUv2 with: [ 3.789394] arm-smmu 8000000.iommu: stage 1 translation [ 3.794845] arm-smmu 8000000.iommu: stage 2 translation [ 3.800294] arm-smmu 8000000.iommu: nested translation [ 3.805657] arm-smmu 8000000.iommu: stream matching with 128 register groups [ 3.812985] arm-smmu 8000000.iommu: 128 context banks (0 stage-2 only) [ 3.821735] arm-smmu 8000000.iommu: Supported page sizes: 0x00001000 [ 3.828352] arm-smmu 8000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 3.834961] arm-smmu 8000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 3.842305] arm-smmu-suspend 12000000.smmu_suspend: arm_smmu_suspend probe successful [ 3.852044] tegra_profiler: version: 1.151, samples/io: 51/30 [ 3.858005] tegra_profiler: auth: init [ 3.862180] nvsciipc: loaded module [ 3.867416] tun: Universal TUN/TAP device driver, 1.6 [ 3.873135] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 3.880562] hns3: Copyright (c) 2017 Huawei Corporation. [ 3.886041] e1000e: Intel(R) PRO/1000 Network Driver [ 3.891136] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.897222] igb: Intel(R) Gigabit Ethernet Network Driver [ 3.902749] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.908642] PPP generic driver version 2.4.2 [ 3.913089] PPP BSD Compression module registered [ 3.917922] PPP Deflate Compression module registered [ 3.923127] PPP MPPE Compression module registered [ 3.928068] usbcore: registered new interface driver r8152 [ 3.933713] usbcore: registered new interface driver asix [ 3.939254] usbcore: registered new interface driver ax88179_178a [ 3.945524] usbcore: registered new interface driver cdc_ether [ 3.951513] usbcore: registered new interface driver net1080 [ 3.957330] usbcore: registered new interface driver cdc_subset [ 3.963401] usbcore: registered new interface driver zaurus [ 3.969132] usbcore: registered new interface driver cdc_ncm [ 3.974962] usbcore: registered new interface driver aqc111 [ 3.980815] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.987163] ohci-pci: OHCI PCI platform driver [ 3.991735] ohci-platform: OHCI generic platform driver [ 3.997406] tegra-xusb 3610000.xhci: Adding to iommu group 0 [ 4.003744] usbcore: registered new interface driver uas [ 4.009220] usbcore: registered new interface driver usb-storage [ 4.015601] mousedev: PS/2 mouse device common for all mice [ 4.021336] usbcore: registered new interface driver xpad [ 4.028748] tegra_rtc c2a0000.rtc: registered as rtc1 [ 4.034207] tegra_rtc c2a0000.rtc: setting system clock to 1970-01-01T00:00:24 UTC (24) [ 4.042428] tegra_rtc c2a0000.rtc: Tegra internal Real Time Clock [ 4.048847] i2c /dev entries driver [ 4.052558] tegra-i2c 3160000.i2c: Adding to iommu group 1 [ 4.058364] tegra-i2c c240000.i2c: Adding to iommu group 1 [ 4.064058] tegra-i2c 3180000.i2c: Adding to iommu group 1 [ 4.069747] tegra-i2c 3190000.i2c: Adding to iommu group 1 [ 4.075415] tegra-i2c 31b0000.i2c: Adding to iommu group 1 [ 4.081089] tegra-i2c 31c0000.i2c: Adding to iommu group 1 [ 4.086760] tegra-i2c c250000.i2c: Adding to iommu group 1 [ 4.092422] tegra-i2c 31e0000.i2c: Adding to iommu group 1 [ 4.100953] pps pps0: new PPS source ktimer [ 4.105254] pps pps0: ktimer PPS source registered [ 4.110184] pps_ldisc: PPS line discipline registered [ 4.116297] device-mapper: uevent: version 1.0.3 [ 4.121117] device-mapper: ioctl: 4.43.0-ioctl (2020-10-01) initialised: dm-devel@redhat.com [ 4.130815] sdhci: Secure Digital Host Controller Interface driver [ 4.137162] sdhci: Copyright(c) Pierre Ossman [ 4.141624] Synopsys Designware Multimedia Card Interface Driver [ 4.147869] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.154351] SMCCC: SOC_ID: ID = jep106:036b:0023 Revision = 0x00000401 [ 4.162012] tegra-bpmp bpmp: firmware: a5fd653d3815177549cc-fcc6f4f897a [ 4.170738] nvvrs_pseq 4-003c: NVVRS Vendor ID: 0x9 [ 4.176575] nvvrs_pseq 4-003c: NVVRS Model Rev: 0x82 [ 4.190845] nvvrs-pseq-rtc nvvrs-pseq-rtc: registered as rtc0 [ 4.196779] nvvrs_pseq 4-003c: NVVRS PSEQ probe successful debugfs initialized [ 5.532521] hid: raw HID events driver (C) Jiri Kosina [ 5.538325] usbcore: registered new interface driver usbhid [ 5.544058] usbhid: USB HID core driver [ 5.548437] tegra-dce d800000.dce: Adding to iommu group 2 [ 5.556001] dce: dce_ipc_channel_init:319 Invalid Channel State [0x0] for ch_type [2] [ 5.564889] tegra234-aon c000000.aon: Adding to iommu group 3 [ 5.571516] dce: dce_mailbox_set_full_interrupt:165 Intr bit set multiple times for MB : [0x5] [ 5.580068] c000000.aon:hsp: probed [ 5.580656] dce: dce_admin_send_cmd_ver:424 version : [0x2] err : [0x0] [ 5.591067] tegra234-aon c000000.aon: init done [ 5.591566] tegra23x-psc e860000.psc: Adding to iommu group 4 [ 5.595866] dce: dce_mailbox_set_full_interrupt:165 Intr bit set multiple times for MB : [0x1] [ 5.601936] tegra23x-psc e860000.psc: ext_cfg base:0000000066bba609 [ 5.610613] dce: dce_admin_setup_clients_ipc:553 Channel Reset Complete for Type [1] ... [ 5.617037] tegra23x-psc e860000.psc: init done [ 5.617238] tegra186-cam-rtcpu bc00000.rtcpu: Adding to iommu group 5 [ 5.625458] dce: dce_admin_setup_clients_ipc:529 Get queue info failed for [2] [ 5.631030] tegra186-cam-rtcpu bc00000.rtcpu: Trace buffer configured at IOVA=0xbff00000 [ 5.636856] dce: dce_mailbox_set_full_interrupt:165 Intr bit set multiple times for MB : [0x2] [ 5.661575] dce: dce_admin_setup_clients_ipc:553 Channel Reset Complete for Type [3] ... [ 5.670229] dce: dce_start_boot_flow:173 DCE_BOOT_DONE [ 5.678171] tegra-ivc-bus bc00000.rtcpu:ivc-bus: region 0: iova=0xbfec0000-0xbfee01ff size=131584 [ 5.687404] tegra-ivc-bus bc00000.rtcpu:ivc-bus:echo@0: echo: ver=0 grp=1 RX[16x64]=0x1000-0x1480 TX[16x64]=0x1480-0x1900 [ 5.699067] tegra-ivc-bus bc00000.rtcpu:ivc-bus:dbg@1: dbg: ver=0 grp=1 RX[1x448]=0x1900-0x1b40 TX[1x448]=0x1b40-0x1d80 [ 5.710541] tegra-ivc-bus bc00000.rtcpu:ivc-bus:dbg@2: dbg: ver=0 grp=1 RX[1x8192]=0x1d80-0x3e00 TX[1x8192]=0x3e00-0x5e80 [ 5.722333] tegra-ivc-bus bc00000.rtcpu:ivc-bus:ivccontrol@3: ivccontrol: ver=0 grp=1 RX[64x320]=0x5e80-0xaf00 TX[64x320]=0xaf00-0xff80 [ 5.734937] tegra-ivc-bus bc00000.rtcpu:ivc-bus:ivccapture@4: ivccapture: ver=0 grp=1 RX[512x64]=0xff80-0x18000 TX[512x64]=0x18000-0x20080 [ 5.747783] tegra-ivc-bus bc00000.rtcpu:ivc-bus:diag@5: diag: ver=0 grp=1 RX[1x64]=0x20080-0x20140 TX[1x64]=0x20140-0x20200 [ 5.760303] tegra186-cam-rtcpu bc00000.rtcpu: using cam RTCPU IRQ (114) [ 5.767108] tegra186-cam-rtcpu bc00000.rtcpu: tegra_camrtc_mon_create is successful [ 5.775440] tegra-hsp b950000.tegra-hsp: Try increasing MBOX_TX_QUEUE_LEN [ 5.775445] tegra186-cam-rtcpu bc00000.rtcpu: firmware version cpu=rce cmd=6 sha1=55ecd57df677fd722e795b49ccb283f065b222a1 [ 5.782409] tegra-hsp b950000.tegra-hsp: Try increasing MBOX_TX_QUEUE_LEN [ 5.782413] tegra-hsp b950000.tegra-hsp: Try increasing MBOX_TX_QUEUE_LEN [ 5.795906] t19x_cache tegra-cache: probed [ 5.812138] scf-pmu-drv scf-pmu: Registered T23x SCF Uncore PMU [ 5.822261] optee: probing Ifor conduit method. /TC: Reserved shared memory is disabled I/TC: Dynamic shared memory is enabled I/TC: Normal World virtualization support is disabled I/TC: Asynchronous notifications are disabled [ 5.826871] optee: revision 3.22 (06437d8c) [ 5.885670] optee: dynamic shared memory is enabled [ 5.895090] optee: initialized driver [ 5.912049] nvpmodel: initialized successfully [ 5.916726] tegra_hv: get_hvd: not initialized yet [ 5.921668] user_ivc_mempool: hypervisor not present [ 5.927589] usbcore: registered new interface driver snd-usb-audio [ 5.935025] u32 classifier [ 5.937816] input device check on [ 5.941590] Actions configured [ 5.945240] Initializing XFRM netlink socket [ 5.950052] NET: Registered protocol family 10 [ 5.956686] Segment Routing with IPv6 [ 5.960543] NET: Registered protocol family 17 [ 5.965137] NET: Registered protocol family 15 [ 5.969771] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 5.983644] Bluetooth: RFCOMM socket layer initialized [ 5.988944] Bluetooth: RFCOMM ver 1.11 [ 5.992809] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 5.998901] Bluetooth: HIDP socket layer initialized [ 6.004946] 9pnet: Installing 9P2000 support [ 6.009401] Key type dns_resolver registered [ 6.014602] registered taskstats version 1 [ 6.018828] Loading compiled-in X.509 certificates [ 6.036103] Loaded X.509 cert 'Build time autogenerated kernel key: 20c736eeef9ce3d19b223fe1b8299549353dc50c' [ 6.046848] tegra194-pcie 14100000.pcie: Adding to iommu group 6 [ 6.059592] tegra194-pcie 14100000.pcie: Using GICv2m MSI allocator [ 6.066933] tegra194-pcie 14160000.pcie: Adding to iommu group 7 [ 6.079304] tegra194-pcie 14160000.pcie: Using GICv2m MSI allocator [ 6.086200] tegra194-pcie 141e0000.pcie: Adding to iommu group 8 [ 6.098258] tegra194-pcie 141e0000.pcie: Using GICv2m MSI allocator [ 6.105088] tegra194-pcie 140a0000.pcie: Adding to iommu group 9 [ 6.117151] tegra194-pcie 140a0000.pcie: Using GICv2m MSI allocator [ 6.124228] tegra194-pcie 140c0000.pcie: Adding to iommu group 10 [ 6.136424] tegra194-pcie 140c0000.pcie: Using GICv2m MSI allocator [ 6.167716] tegra-soc-hwpm f100000.tegra_soc_hwpm: Adding to iommu group 11 [ 6.180602] simple-framebuffer chosen:framebuffer: framebuffer at 0x279e00000, 0x870000 bytes, mapped to 0x00000000a638aa2f [ 6.192063] simple-framebuffer chosen:framebuffer: format=x8r8g8b8, mode=1920x1080x32, linelength=8192 [ 6.201644] fb0: switching to simple from EFI VGA [ 6.207149] Console: switching to colour dummy device 80x25 [ 6.216099] Console: switching to colour frame buffer device 240x67 [ 6.225316] simple-framebuffer chosen:framebuffer: fb0: simplefb registered! [ 6.232836] host1x 13e40000.host1x: Adding to iommu group 12 [ 6.265106] host1x 13e40000.host1x: initialized [ 6.270128] iommu_context_dev 13e40000.host1x:niso0_ctx0: Adding to iommu group 13 [ 6.278162] iommu_context_dev 13e40000.host1x:niso0_ctx0: initialized (streamid=53, iommu=smmu.0x0000000012000000) [ 6.290186] iommu_context_dev 13e40000.host1x:niso0_ctx1: Adding to iommu group 14 [ 6.298202] iommu_context_dev 13e40000.host1x:niso0_ctx1: initialized (streamid=54, iommu=smmu.0x0000000012000000) [ 6.310205] iommu_context_dev 13e40000.host1x:niso0_ctx2: Adding to iommu group 15 [ 6.318179] iommu_context_dev 13e40000.host1x:niso0_ctx2: initialized (streamid=55, iommu=smmu.0x0000000012000000) [ 6.330147] iommu_context_dev 13e40000.host1x:niso0_ctx3: Adding to iommu group 16 [ 6.338173] iommu_context_dev 13e40000.host1x:niso0_ctx3: initialized (streamid=56, iommu=smmu.0x0000000012000000) [ 6.350139] iommu_context_dev 13e40000.host1x:niso0_ctx4: Adding to iommu group 17 [ 6.358093] iommu_context_dev 13e40000.host1x:niso0_ctx4: initialized (streamid=57, iommu=smmu.0x0000000012000000) [ 6.370091] iommu_context_dev 13e40000.host1x:niso0_ctx5: Adding to iommu group 18 [ 6.378056] iommu_context_dev 13e40000.host1x:niso0_ctx5: initialized (streamid=58, iommu=smmu.0x0000000012000000) [ 6.390037] iommu_context_dev 13e40000.host1x:niso0_ctx6: Adding to iommu group 19 [ 6.398012] iommu_context_dev 13e40000.host1x:niso0_ctx6: initialized (streamid=59, iommu=smmu.0x0000000012000000) [ 6.410020] iommu_context_dev 13e40000.host1x:niso0_ctx7: Adding to iommu group 20 [ 6.418011] iommu_context_dev 13e40000.host1x:niso0_ctx7: initialized (streamid=60, iommu=smmu.0x0000000012000000) [ 6.430005] iommu_context_dev 13e40000.host1x:niso1_ctx0: Adding to iommu group 21 [ 6.437983] iommu_context_dev 13e40000.host1x:niso1_ctx0: initialized (streamid=53, iommu=smmu.0x0000000008000000) [ 6.449985] iommu_context_dev 13e40000.host1x:niso1_ctx1: Adding to iommu group 22 [ 6.457989] iommu_context_dev 13e40000.host1x:niso1_ctx1: initialized (streamid=54, iommu=smmu.0x0000000008000000) [ 6.469982] iommu_context_dev 13e40000.host1x:niso1_ctx2: Adding to iommu group 23 [ 6.477948] iommu_context_dev 13e40000.host1x:niso1_ctx2: initialized (streamid=55, iommu=smmu.0x0000000008000000) [ 6.489933] iommu_context_dev 13e40000.host1x:niso1_ctx3: Adding to iommu group 24 [ 6.497905] iommu_context_dev 13e40000.host1x:niso1_ctx3: initialized (streamid=56, iommu=smmu.0x0000000008000000) [ 6.509917] iommu_context_dev 13e40000.host1x:niso1_ctx4: Adding to iommu group 25 [ 6.517890] iommu_context_dev 13e40000.host1x:niso1_ctx4: initialized (streamid=57, iommu=smmu.0x0000000008000000) [ 6.529865] iommu_context_dev 13e40000.host1x:niso1_ctx5: Adding to iommu group 26 [ 6.537843] iommu_context_dev 13e40000.host1x:niso1_ctx5: initialized (streamid=58, iommu=smmu.0x0000000008000000) [ 6.549829] iommu_context_dev 13e40000.host1x:niso1_ctx6: Adding to iommu group 27 [ 6.557807] iommu_context_dev 13e40000.host1x:niso1_ctx6: initialized (streamid=59, iommu=smmu.0x0000000008000000) [ 6.569779] iommu_context_dev 13e40000.host1x:niso1_ctx7: Adding to iommu group 28 [ 6.577744] iommu_context_dev 13e40000.host1x:niso1_ctx7: initialized (streamid=60, iommu=smmu.0x0000000008000000) [ 6.589788] falcon 15340000.vic: Adding to iommu group 29 [ 6.600851] falcon 15340000.vic: initialized [ 6.605558] falcon 15380000.nvjpg: Adding to iommu group 30 [ 6.614140] falcon 15380000.nvjpg: initialized [ 6.618844] falcon 15540000.nvjpg1: Adding to iommu group 31 [ 6.628285] falcon 15540000.nvjpg1: initialized [ 6.633082] falcon 154c0000.nvenc: Adding to iommu group 32 [ 6.643477] falcon 154c0000.nvenc: initialized [ 6.648187] falcon 15a50000.ofa: Adding to iommu group 33 [ 6.657013] falcon 15a50000.ofa: initialized [ 6.661559] nvdec 15480000.nvdec: Adding to iommu group 34 [ 6.674616] nvdec 15480000.nvdec: initialized [ 6.679229] tsec 15500000.tsec: Adding to iommu group 35 [ 6.689952] tsec 15500000.tsec: initialized [ 6.697733] gic 2a41000.agic-controller: GIC IRQ controller registered [ 6.714505] tegra-aconnect aconnect@2a41000: Tegra ACONNECT bus registered [ 6.729057] gpio-397 (camera-control-output-low): hogged as output/low [ 6.735811] gpio-486 (camera-control-output-low): hogged as output/low [ 6.742571] gpio-466 (kenexs_gpio_ctrl_gpio): hogged as output/high [ 6.750107] gpiochip0: registered GPIOs 348 to 511 on tegra234-gpio [ 6.757421] gpiochip1: registered GPIOs 316 to 347 on tegra234-gpio-aon [ 6.764405] tegra-pwm 3280000.pwm: PWM clk can sleep in ops [ 6.770891] tegra-pwm 32a0000.pwm: PWM clk can sleep in ops [ 6.777399] tegra-pwm 32c0000.pwm: PWM clk can sleep in ops [ 6.783671] tegra-pwm 32e0000.pwm: PWM clk can sleep in ops [ 6.792106] tegra194-isp5 14800000.isp: Adding to iommu group 36 [ 6.801194] t194-nvcsi 13e40000.host1x:nvcsi@15a00000: context isolation disabled due to no IOMMU [ 6.810900] t194-nvcsi 13e40000.host1x:nvcsi@15a00000: initialized [ 6.817373] tegra-camrtc-capture-vi tegra-capture-vi: subdev 13e40000.host1x:nvcsi@15a00000- bound [ 6.826612] tegra-camrtc-capture-vi tegra-capture-vi: subdev 13e40000.host1x:nvcsi@15a00000- bound [ 6.836006] tegra194-vi5 13e40000.host1x:vi0@15c00000: Adding to iommu group 37 [ 6.844024] tegra194-vi5 13e40000.host1x:vi1@14c00000: Adding to iommu group 38 [ 6.851982] scare-pigeon 13e40000.host1x:vi0-thi@15f00000: context isolation disabled due to no IOMMU [ 6.861927] scare-pigeon 13e40000.host1x:vi0-thi@15f00000: initialized [ 6.868746] scare-pigeon 13e40000.host1x:vi1-thi@14f00000: context isolation disabled due to no IOMMU [ 6.878728] scare-pigeon 13e40000.host1x:vi1-thi@14f00000: initialized [ 6.885529] scare-pigeon 13e40000.host1x:isp-thi@14b00000: context isolation disabled due to no IOMMU [ 6.895553] scare-pigeon 13e40000.host1x:isp-thi@14b00000: initialized [ 6.902386] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx0: Adding to iommu group 39 [ 6.911034] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx0: initialized (streamid=18, iommu=smmu.0x0000000008000000) [ 6.922413] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx1: Adding to iommu group 40 [ 6.931033] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx1: initialized (streamid=19, iommu=smmu.0x0000000008000000) [ 6.942404] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx2: Adding to iommu group 41 [ 6.950982] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx2: initialized (streamid=20, iommu=smmu.0x0000000008000000) [ 6.962335] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx3: Adding to iommu group 42 [ 6.970930] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx3: initialized (streamid=21, iommu=smmu.0x0000000008000000) [ 6.982304] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx4: Adding to iommu group 43 [ 6.990906] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx4: initialized (streamid=22, iommu=smmu.0x0000000008000000) [ 7.002274] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx5: Adding to iommu group 44 [ 7.010864] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx5: initialized (streamid=23, iommu=smmu.0x0000000008000000) [ 7.022231] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx6: Adding to iommu group 45 [ 7.030795] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx6: initialized (streamid=24, iommu=smmu.0x0000000008000000) [ 7.042173] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx7: Adding to iommu group 46 [ 7.050764] pva_iommu_context_dev 16000000.pva0:pva0_niso1_ctx7: initialized (streamid=25, iommu=smmu.0x0000000008000000) [ 7.062138] pva 16000000.pva0: Adding to iommu group 47 [ 7.073257] pva 16000000.pva0: initialized [ 7.089653] nvdla 15880000.nvdla0: Adding to iommu group 48 [ 7.100146] nvdla 15880000.nvdla0: initialized [ 7.106488] tegra-gpcdma 2600000.gpcdma: Adding to iommu group 1 [ 7.113555] tegra-gpcdma 2600000.gpcdma: GPC DMA driver register 31 channels [ 7.121052] tegra-fuse-burn efuse-burn: shutdown limit check disabled [ 7.127678] tegra-fuse-burn efuse-burn: Fuse burn driver initialized [ 7.134425] serial-tegra 3100000.serial: Adding to iommu group 1 [ 7.141022] 3100000.serial: ttyTHS0 at MMIO 0x3100000 (irq = 17, base_baud = 0) is a TEGRA_UART [ 7.150805] serial-tegra 3130000.serial: Adding to iommu group 1 [ 7.157296] 3130000.serial: ttyTHS3 at MMIO 0x3130000 (irq = 65, base_baud = 0) is a TEGRA_UART [ 7.166563] serial-tegra 3140000.serial: Adding to iommu group 1 [ 7.173096] 3140000.serial: ttyTHS4 at MMIO 0x3140000 (irq = 66, base_baud = 0) is a TEGRA_UART [ 7.200103] tegra-xusb 3610000.xhci: Firmware timestamp: 2023-02-10 03:48:10 UTC, Version: 80.05 release [ 7.209874] tegra-xusb 3610000.xhci: xHCI Host Controller [ 7.215457] tegra-xusb 3610000.xhci: new USB bus registered, assigned bus number 1 [ 7.224103] tegra-xusb 3610000.xhci: hcc params 0x0180ff05 hci version 0x120 quirks 0x0000000000050810 [ 7.233714] tegra-xusb 3610000.xhci: irq 229, io mem 0x03610000 [ 7.240048] tegra-xusb 3610000.xhci: xHCI Host Controller [ 7.245616] tegra-xusb 3610000.xhci: new USB bus registered, assigned bus number 2 [ 7.253409] tegra-xusb 3610000.xhci: Host supports USB 3.1 Enhanced SuperSpeed [ 7.261030] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 7.269535] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.276964] usb usb1: Product: xHCI Host Controller [ 7.281973] usb usb1: Manufacturer: Linux 5.10.192-tegra xhci-hcd [ 7.288242] usb usb1: SerialNumber: 3610000.xhci [ 7.293731] hub 1-0:1.0: USB hub found [ 7.297616] hub 1-0:1.0: 4 ports detected [ 7.302037] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10 [ 7.310545] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.317983] usb usb2: Product: xHCI Host Controller [ 7.322994] usb usb2: Manufacturer: Linux 5.10.192-tegra xhci-hcd [ 7.329275] usb usb2: SerialNumber: 3610000.xhci [ 7.334339] hub 2-0:1.0: USB hub found [ 7.338216] hub 2-0:1.0: 4 ports detected [ 7.361643] i2c i2c-2: Added multiplexed i2c bus 9 [ 7.367255] i2c i2c-2: Added multiplexed i2c bus 10 [ 7.372280] i2c-mux-gpio cam_i2cmux: 2 port mux on 3180000.i2c adapter [ 7.379268] tegra23x-oc-event soctherm-oc-event: Finished tegra23x overcurrent event probing [ 7.401495] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 2019000 KHz, changing to: 1984000 KHz [ 7.414023] cpufreq: cpufreq_online: CPU4: Running at unlisted initial frequency: 1977000 KHz, changing to: 1984000 KHz [ 7.425835] tegra194-cpufreq e000000.ccplex: probed with ICC, cl:3 [ 7.433061] tegra194-pcie 14100000.pcie: Using GICv2m MSI allocator [ 7.440927] tegra194-pcie 14100000.pcie: host bridge /pcie@14100000 ranges: [ 7.448107] tegra194-pcie 14100000.pcie: IO 0x0030100000..0x00301fffff -> 0x0030100000 [ 7.456796] tegra194-pcie 14100000.pcie: MEM 0x20a8000000..0x20afffffff -> 0x0040000000 [ 7.465477] tegra194-pcie 14100000.pcie: MEM 0x2080000000..0x20a7ffffff -> 0x2080000000 [ 7.474242] tegra194-pcie 14100000.pcie: pci->link_gen <= 0 [ 7.559376] usb 1-3: new low-speed USB device number 2 using tegra-xusb [ 7.587375] tegra194-pcie 14100000.pcie: Link up [ 7.593663] tegra194-pcie 14100000.pcie: PCI host bridge to bus 0001:00 [ 7.600487] pci_bus 0001:00: root bus resource [bus 00-ff] [ 7.606123] pci_bus 0001:00: root bus resource [io 0x0000-0xfffff] (bus address [0x30100000-0x301fffff]) [ 7.615951] pci_bus 0001:00: root bus resource [mem 0x20a8000000-0x20afffffff] (bus address [0x40000000-0x47ffffff]) [ 7.626811] pci_bus 0001:00: root bus resource [mem 0x2080000000-0x20a7ffffff pref] [ 7.634742] pci 0001:00:00.0: [10de:229e] type 01 class 0x060400 [ 7.641068] pci 0001:00:00.0: PME# supported from D0 D3hot [ 7.650914] pci 0001:01:00.0: [10ec:8168] type 00 class 0x020000 [ 7.657265] pci 0001:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 7.657267] pci 0001:01:00.0: reg 0x10: [io size 0x0100] [ 7.657464] pci 0001:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 7.677173] pci 0001:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit] [ 7.685220] pci 0001:01:00.0: supports D1 D2 [ 7.689608] pci 0001:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 7.700736] pci 0001:00:00.0: BAR 14: assigned [mem 0x20a8000000-0x20a80fffff] [ 7.708176] pci 0001:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 7.714535] pci 0001:01:00.0: BAR 4: assigned [mem 0x20a8000000-0x20a8003fff 64bit] [ 7.722516] pci 0001:01:00.0: BAR 2: assigned [mem 0x20a8004000-0x20a8004fff 64bit] [ 7.730527] pci 0001:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 7.736848] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 7.742241] pci 0001:00:00.0: bridge window [io 0x1000-0x1fff] [ 7.748529] pci 0001:00:00.0: bridge window [mem 0x20a8000000-0x20a80fffff] [ 7.755907] pci 0001:00:00.0: Max Payload Size set to 128/ 256 (was 256), Max Read Rq 512 [ 7.764614] usb 1-3: New USB device found, idVendor=1c4f, idProduct=0002, bcdDevice= 1.50 [ 7.764679] pci 0001:01:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 512 [ 7.773062] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 7.781952] pcieport 0001:00:00.0: Adding to iommu group 6 [ 7.789051] usb 1-3: Product: USB Keyboard [ 7.789052] usb 1-3: Manufacturer: SIGMACHIP [ 7.803606] pcieport 0001:00:00.0: PME: Signaling with IRQ 55 [ 7.810032] pcieport 0001:00:00.0: AER: enabled with IRQ 55 [ 7.816054] input: SIGMACHIP USB Keyboard as /devices/platform/3610000.xhci/usb1/1-3/1-3:1.0/0003:1C4F:0002.0001/input/input0 [ 7.816566] tegra194-pcie 14160000.pcie: Using GICv2m MSI allocator [ 7.835700] tegra194-pcie 14160000.pcie: host bridge /pcie@14160000 ranges: [ 7.842879] tegra194-pcie 14160000.pcie: IO 0x0036100000..0x00361fffff -> 0x0036100000 [ 7.851569] tegra194-pcie 14160000.pcie: MEM 0x2428000000..0x242fffffff -> 0x0040000000 [ 7.860259] tegra194-pcie 14160000.pcie: MEM 0x2140000000..0x2427ffffff -> 0x2140000000 [ 7.868966] tegra194-pcie 14160000.pcie: target speed: 3 [ 7.874421] tegra194-pcie 14160000.pcie: Trying from Link gen-1 [ 7.880598] tegra194-pcie 14160000.pcie: set max speed link_gen=3 [ 7.886879] tegra194-pcie 14160000.pcie: link_cap > 2, force set link speed to gen-1, but remain link cap to be 3 [ 7.888572] hid-generic 0003:1C4F:0002.0001: input,hidraw0: USB HID v1.10 Keyboard [SIGMACHIP USB Keyboard] on usb-3610000.xhci-3/input0 [ 7.912946] input: SIGMACHIP USB Keyboard Consumer Control as /devices/platform/3610000.xhci/usb1/1-3/1-3:1.1/0003:1C4F:0002.0002/input/input1 [ 7.984089] input: SIGMACHIP USB Keyboard System Control as /devices/platform/3610000.xhci/usb1/1-3/1-3:1.1/0003:1C4F:0002.0002/input/input2 [ 7.997613] hid-generic 0003:1C4F:0002.0002: input,hidraw1: USB HID v1.10 Device [SIGMACHIP USB Keyboard] on usb-3610000.xhci-3/input1 [ 8.003374] tegra194-pcie 14160000.pcie: Link up [ 8.014806] tegra194-pcie 14160000.pcie: Link(gen-1) is up(1/10), trying to switch to higher [ 8.023477] tegra194-pcie 14160000.pcie: dw_pcie link set link_gen=3 [ 9.031621] tegra194-pcie 14160000.pcie: Link Training Timeout [ 9.037623] tegra194-pcie 14160000.pcie: Link gen-3 failed to up, retrying(1/10), gen-1: 1/10, target link width: 3 [ 9.048344] tegra194-pcie 14160000.pcie: dw_pcie link set link_gen=3 [ 9.054875] tegra194-pcie 14160000.pcie: Link speed is already at the target speed: 3GT/s [ 10.063758] tegra194-pcie 14160000.pcie: Link Retrain Timeout [ 10.069665] tegra194-pcie 14160000.pcie: Link gen-3 failed to up, retrying(2/10), gen-1: 1/10, target link width: 3 [ 10.080385] tegra194-pcie 14160000.pcie: dw_pcie link set link_gen=3 [ 10.086916] tegra194-pcie 14160000.pcie: Link speed is already at the target speed: 3GT/s [ 10.867381] [RCE] WARNING: core/hsp/hsp-vm.c:283 [camrtc_hsp_full_ss_isr] "VM0 issued IVC in inactive state." [ 10.877595] [RCE] WARNING: core/hsp/hsp-vm.c:283 [camrtc_hsp_full_ss_isr] "VM0 issued IVC in inactive state." [ 10.887799] [RCE] WARNING: core/hsp/hsp-vm.c:283 [camrtc_hsp_full_ss_isr] "VM0 issued IVC in inactive state." [ 11.743491] tegra194-pcie 14160000.pcie: Bandwidth Management Status Timeout [ 11.750748] tegra194-pcie 14160000.pcie: Link gen-3 failed to up, retrying(3/10), gen-1: 1/10, target link width: 3 [ 11.761491] tegra194-pcie 14160000.pcie: dw_pcie link set link_gen=3 [ 11.768026] tegra194-pcie 14160000.pcie: Link speed is already at the target speed: 3GT/s [ 11.803375] tegra194-pcie 14160000.pcie: Link speed is successful [ 11.809642] tegra194-pcie 14160000.pcie: Link(gen-3) is up [ 11.816477] tegra194-pcie 14160000.pcie: PCI host bridge to bus 0004:00 [ 11.823289] pci_bus 0004:00: root bus resource [bus 00-ff] [ 11.828933] pci_bus 0004:00: root bus resource [io 0x100000-0x1fffff] (bus address [0x36100000-0x361fffff]) [ 11.839048] pci_bus 0004:00: root bus resource [mem 0x2428000000-0x242fffffff] (bus address [0x40000000-0x47ffffff]) [ 11.849873] pci_bus 0004:00: root bus resource [mem 0x2140000000-0x2427ffffff pref] [ 11.857793] pci 0004:00:00.0: [10de:229c] type 01 class 0x060400 [ 11.864101] pci 0004:00:00.0: PME# supported from D0 D3hot [ 11.873997] pci 0004:01:00.0: [1d6a:14c0] type 00 class 0x020000 [ 11.880357] pci 0004:01:00.0: reg 0x10: [mem 0x00000000-0x0007ffff 64bit] [ 11.887449] pci 0004:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 11.894526] pci 0004:01:00.0: reg 0x20: [mem 0x00000000-0x003fffff 64bit] [ 11.901554] pci 0004:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref] [ 11.909623] pci 0004:01:00.0: supports D1 D2 [ 11.914012] pci 0004:01:00.0: PME# supported from D0 D1 D3hot D3cold [ 11.924982] pci 0004:00:00.0: BAR 14: assigned [mem 0x2428000000-0x24285fffff] [ 11.932413] pci 0004:01:00.0: BAR 4: assigned [mem 0x2428000000-0x24283fffff 64bit] [ 11.940391] pci 0004:01:00.0: BAR 0: assigned [mem 0x2428400000-0x242847ffff 64bit] [ 11.948355] pci 0004:01:00.0: BAR 6: assigned [mem 0x2428480000-0x242849ffff pref] [ 11.956139] pci 0004:01:00.0: BAR 2: assigned [mem 0x24284a0000-0x24284a0fff 64bit] [ 11.964095] pci 0004:00:00.0: PCI bridge to [bus 01-ff] [ 11.969462] pci 0004:00:00.0: bridge window [mem 0x2428000000-0x24285fffff] [ 11.976816] pci 0004:00:00.0: Max Payload Size set to 256/ 256 (was 256), Max Read Rq 512 [ 11.985552] pci 0004:01:00.0: Max Payload Size set to 256/ 512 (was 128), Max Read Rq 512 [ 11.994484] pcieport 0004:00:00.0: Adding to iommu group 7 [ 12.000341] pcieport 0004:00:00.0: PME: Signaling with IRQ 57 [ 12.006753] pcieport 0004:00:00.0: AER: enabled with IRQ 57 [ 12.013311] tegra194-pcie 141e0000.pcie: Using GICv2m MSI allocator [ 12.020909] tegra194-pcie 141e0000.pcie: host bridge /pcie@141e0000 ranges: [ 12.028083] tegra194-pcie 141e0000.pcie: IO 0x003e100000..0x003e1fffff -> 0x003e100000 [ 12.036771] tegra194-pcie 141e0000.pcie: MEM 0x3228000000..0x322fffffff -> 0x0040000000 [ 12.045450] tegra194-pcie 141e0000.pcie: MEM 0x2e40000000..0x3227ffffff -> 0x2e40000000 [ 12.054212] tegra194-pcie 141e0000.pcie: pci->link_gen <= 0 [ 12.167384] tegra194-pcie 141e0000.pcie: Link up [ 12.173162] tegra194-pcie 141e0000.pcie: PCI host bridge to bus 0007:00 [ 12.179966] pci_bus 0007:00: root bus resource [bus 00-ff] [ 12.185598] pci_bus 0007:00: root bus resource [io 0x200000-0x2fffff] (bus address [0x3e100000-0x3e1fffff]) [ 12.195702] pci_bus 0007:00: root bus resource [mem 0x3228000000-0x322fffffff] (bus address [0x40000000-0x47ffffff]) [ 12.206534] pci_bus 0007:00: root bus resource [mem 0x2e40000000-0x3227ffffff pref] [ 12.214453] pci 0007:00:00.0: [10de:229a] type 01 class 0x060400 [ 12.220747] pci 0007:00:00.0: PME# supported from D0 D3hot [ 12.230302] pci 0007:01:00.0: [2646:5017] type 00 class 0x010802 [ 12.236625] pci 0007:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit] [ 12.244997] pci 0007:01:00.0: 15.753 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x1 link at 0007:00:00.0 (capable of 63.012 Gb/s with 16.0 GT/s PCIe x4 link) [ 12.264242] pci 0007:00:00.0: BAR 14: assigned [mem 0x3228000000-0x32280fffff] [ 12.271670] pci 0007:01:00.0: BAR 0: assigned [mem 0x3228000000-0x3228003fff 64bit] [ 12.279600] pci 0007:00:00.0: PCI bridge to [bus 01-ff] [ 12.284974] pci 0007:00:00.0: bridge window [mem 0x3228000000-0x32280fffff] [ 12.292319] pci 0007:00:00.0: Max Payload Size set to 128/ 256 (was 256), Max Read Rq 512 [ 12.301053] pci 0007:01:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 512 [ 12.309969] pcieport 0007:00:00.0: Adding to iommu group 8 [ 12.315804] pcieport 0007:00:00.0: PME: Signaling with IRQ 59 [ 12.322481] pcieport 0007:00:00.0: AER: enabled with IRQ 59 [ 12.328497] nvme 0007:01:00.0: Adding to iommu group 8 [ 12.334205] nvme nvme0: pci function 0007:01:00.0 [ 12.339110] nvme 0007:01:00.0: enabling device (0000 -> 0002) [ 12.339681] tegra194-pcie 140a0000.pcie: Using GICv2m MSI allocator [ 12.352097] tegra194-pcie 140c0000.pcie: Using GICv2m MSI allocator [ 12.359954] tegra194-pcie 140c0000.pcie: host bridge /pcie@140c0000 ranges: [ 12.367129] tegra194-pcie 140c0000.pcie: IO 0x002c100000..0x002c1fffff -> 0x002c100000 [ 12.375816] tegra194-pcie 140c0000.pcie: MEM 0x3828000000..0x382fffffff -> 0x0040000000 [ 12.378772] nvme nvme0: allocated 64 MiB host memory buffer. [ 12.384496] tegra194-pcie 140c0000.pcie: MEM 0x3540000000..0x3827ffffff -> 0x3540000000 [ 12.384581] tegra194-pcie 140c0000.pcie: pci->link_gen <= 0 [ 12.416117] nvme nvme0: 6/0/0 default/read/poll queues [ 12.435064] nvme0n1: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 [ 12.511532] tegra194-pcie 140c0000.pcie: Link up [ 12.517350] tegra194-pcie 140c0000.pcie: PCI host bridge to bus 0009:00 [ 12.524151] pci_bus 0009:00: root bus resource [bus 00-ff] [ 12.529787] pci_bus 0009:00: root bus resource [io 0x300000-0x3fffff] (bus address [0x2c100000-0x2c1fffff]) [ 12.539900] pci_bus 0009:00: root bus resource [mem 0x3828000000-0x382fffffff] (bus address [0x40000000-0x47ffffff]) [ 12.550732] pci_bus 0009:00: root bus resource [mem 0x3540000000-0x3827ffffff pref] [ 12.558662] pci 0009:00:00.0: [10de:229c] type 01 class 0x060400 [ 12.564982] pci 0009:00:00.0: PME# supported from D0 D3hot [ 12.574703] pci 0009:01:00.0: [10ec:8168] type 00 class 0x020000 [ 12.581029] pci 0009:01:00.0: reg 0x10: [io 0x0000-0x00ff] [ 12.586934] pci 0009:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 12.594038] pci 0009:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit] [ 12.602024] pci 0009:01:00.0: supports D1 D2 [ 12.606415] pci 0009:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 12.617445] pci 0009:00:00.0: BAR 14: assigned [mem 0x3828000000-0x38280fffff] [ 12.624880] pci 0009:00:00.0: BAR 13: assigned [io 0x300000-0x300fff] [ 12.631599] pci 0009:01:00.0: BAR 4: assigned [mem 0x3828000000-0x3828003fff 64bit] [ 12.639577] pci 0009:01:00.0: BAR 2: assigned [mem 0x3828004000-0x3828004fff 64bit] [ 12.647546] pci 0009:01:00.0: BAR 0: assigned [io 0x300000-0x3000ff] [ 12.654202] pci 0009:00:00.0: PCI bridge to [bus 01-ff] [ 12.659570] pci 0009:00:00.0: bridge window [io 0x300000-0x300fff] [ 12.666202] pci 0009:00:00.0: bridge window [mem 0x3828000000-0x38280fffff] [ 12.673562] pci 0009:00:00.0: Max Payload Size set to 128/ 256 (was 256), Max Read Rq 512 [ 12.682305] pci 0009:01:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 512 [ 12.691253] pcieport 0009:00:00.0: Adding to iommu group 10 [ 12.697203] pcieport 0009:00:00.0: PME: Signaling with IRQ 63 [ 12.703895] pcieport 0009:00:00.0: AER: enabled with IRQ 63 [ 12.710059] vdd-3v3-sd: supplied by vdd-3v3 [ 12.714685] vcc_5v_usb: supplied by vcc_24 [ 12.719105] vbus_a_5(usb2): supplied by vcc_5v_usb [ 12.724182] vbus_a_6(usb3-1): supplied by vcc_5v_usb [ 12.729380] reg-fixed-voltage fixed-regulators:vbus_a_3: nonexclusive access to GPIO for fixed-regulators:vbus_a_3 [ 12.740032] vbus_a_3(usb3-2): supplied by vcc_5v_usb [ 12.745247] vbus_a_3(usb3-3): supplied by vcc_5v_usb [ 12.752850] tegra194-isp5 14800000.isp: initialized [ 12.761588] tegra194-vi5 13e40000.host1x:vi0@15c00000: initialized [ 12.768049] (NULL device *): fops function table already registered [ 12.775618] tegra194-vi5 13e40000.host1x:vi1@14c00000: initialized [ 12.782474] tegra194-pcie 140a0000.pcie: Using GICv2m MSI allocator [ 12.789286] irq: IRQ300: trimming hierarchy from :interrupt-controller@f400000-1 [ 12.904382] tegra194-pcie 140a0000.pcie: host bridge /pcie@140a0000 ranges: [ 12.911565] tegra194-pcie 140a0000.pcie: IO 0x002a100000..0x002a1fffff -> 0x002a100000 [ 12.920256] tegra194-pcie 140a0000.pcie: MEM 0x3528000000..0x352fffffff -> 0x0040000000 [ 12.928933] tegra194-pcie 140a0000.pcie: MEM 0x3240000000..0x3527ffffff -> 0x3240000000 [ 12.937706] tegra194-pcie 140a0000.pcie: pci->link_gen <= 0 [ 13.051531] tegra194-pcie 140a0000.pcie: Link up [ 13.057341] tegra194-pcie 140a0000.pcie: PCI host bridge to bus 0008:00 [ 13.064159] pci_bus 0008:00: root bus resource [bus 00-ff] [ 13.069796] pci_bus 0008:00: root bus resource [io 0x400000-0x4fffff] (bus address [0x2a100000-0x2a1fffff]) [ 13.079895] pci_bus 0008:00: root bus resource [mem 0x3528000000-0x352fffffff] (bus address [0x40000000-0x47ffffff]) [ 13.090723] pci_bus 0008:00: root bus resource [mem 0x3240000000-0x3527ffffff pref] [ 13.098632] pci 0008:00:00.0: [10de:229c] type 01 class 0x060400 [ 13.104955] pci 0008:00:00.0: PME# supported from D0 D3hot [ 13.114758] pci 0008:01:00.0: [10ec:8168] type 00 class 0x020000 [ 13.121083] pci 0008:01:00.0: reg 0x10: [io 0x0000-0x00ff] [ 13.126999] pci 0008:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit] [ 13.134084] pci 0008:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit] [ 13.142095] pci 0008:01:00.0: supports D1 D2 [ 13.146486] pci 0008:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 13.157562] pci 0008:00:00.0: BAR 14: assigned [mem 0x3528000000-0x35280fffff] [ 13.164995] pci 0008:00:00.0: BAR 13: assigned [io 0x400000-0x400fff] [ 13.171714] pci 0008:01:00.0: BAR 4: assigned [mem 0x3528000000-0x3528003fff 64bit] [ 13.179683] pci 0008:01:00.0: BAR 2: assigned [mem 0x3528004000-0x3528004fff 64bit] [ 13.187653] pci 0008:01:00.0: BAR 0: assigned [io 0x400000-0x4000ff] [ 13.194309] pci 0008:00:00.0: PCI bridge to [bus 01-ff] [ 13.199685] pci 0008:00:00.0: bridge window [io 0x400000-0x400fff] [ 13.206318] pci 0008:00:00.0: bridge window [mem 0x3528000000-0x35280fffff] [ 13.213672] pci 0008:00:00.0: Max Payload Size set to 128/ 256 (was 256), Max Read Rq 512 [ 13.222415] pci 0008:01:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 512 [ 13.231345] pcieport 0008:00:00.0: Adding to iommu group 9 [ 13.237209] pcieport 0008:00:00.0: PME: Signaling with IRQ 61 [ 13.243890] pcieport 0008:00:00.0: AER: enabled with IRQ 61 [ 13.251127] irq: IRQ302: trimming hierarchy from :pmc@c360000 [ 13.257136] irq: IRQ303: trimming hierarchy from :interrupt-controller@f400000-1 [ 13.264826] input: gpio-keys as /devices/platform/gpio-keys/input/input3 [ 13.272479] tegra-se-nvhost 15810000.se: Adding to iommu group 49 [ 13.279061] tegra-se-nvhost 15810000.se: initialized [ 13.293085] tegra-se-nvhost 15810000.se: tegra_se_probe: complete [ 13.299442] tegra-se-nvhost 15820000.se: Adding to iommu group 50 [ 13.305973] tegra-se-nvhost 15820000.se: initialized [ 13.313384] tegra-se-nvhost 15820000.se: tegra_se_probe: complete [ 13.319755] tegra-se-nvhost 15840000.se: Adding to iommu group 51 [ 13.326282] tegra-se-nvhost 15840000.se: initialized [ 13.334531] tegra-se-nvhost 15840000.se: tegra_se_probe: complete [ 13.341372] tegra_actmon d230000.actmon: in actmon_register()... [ 13.347692] tegra_actmon d230000.actmon: bwmgr_disable = 1 [ 13.353697] tegra_actmon d230000.actmon: initialization Completed for the device mc_all [ 13.362082] hvc_sysfs: hypervisor is not present WARNING: clock_disable: clk_power_ungate on gated domain 35 for gpc1clk [ 13.401936] ALSA device list: [ 13.404993] No soundcards found. [ 13.409122] Freeing unused kernel memory: 3968K [ 13.413857] Run /init as init process [ 13.429591] Root device found: PARTUUID=6efa5acd-5d4c-4a28-92b7-fd3e6762f352 [ 13.699094] EXT4-fs (nvme0n1p1): mounted filesystem with ordered data mode. Opts: (null) [ 13.711992] Rootfs mounted over PARTUUID=6efa5acd-5d4c-4a28-92b7-fd3e6762f352 [ 13.725145] Switching from initrd to actual rootfs [ 13.769951] systemd[1]: System time before build time, advancing clock. [ 13.828226] systemd[1]: systemd 245.4-4ubuntu3.23 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default) [ 13.851775] systemd[1]: Detected architecture arm64. [ 13.907491] systemd[1]: Set hostname to . [ 14.008169] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 14.020977] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 14.030510] systemd[1]: Created slice system-getty.slice. [ 14.051650] systemd[1]: Created slice system-modprobe.slice. [ 14.071627] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 14.091678] systemd[1]: Created slice User and Session Slice. [ 14.111469] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 14.135444] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 14.159614] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 14.183417] systemd[1]: Reached target Local Encrypted Volumes. [ 14.203413] systemd[1]: Reached target Remote File Systems. [ 14.223394] systemd[1]: Reached target Slices. [ 14.239398] systemd[1]: Reached target Swap. [ 14.255540] systemd[1]: Listening on fsck to fsckd communication Socket. [ 14.279452] systemd[1]: Listening on initctl Compatibility Named Pipe. [ 14.303601] systemd[1]: Listening on Journal Audit Socket. [ 14.327499] systemd[1]: Listening on Journal Socket (/dev/log). [ 14.351507] systemd[1]: Listening on Journal Socket. [ 14.375508] systemd[1]: Listening on udev Control Socket. [ 14.395467] systemd[1]: Listening on udev Kernel Socket. [ 14.416382] systemd[1]: Mounting Huge Pages File System... [ 14.436323] systemd[1]: Mounting POSIX Message Queue File System... [ 14.456309] systemd[1]: Mounting Kernel Debug File System... [ 14.476405] systemd[1]: Mounting Kernel Trace File System... [ 14.495747] systemd[1]: tmp.mount: Directory /tmp to mount over is not empty, mounting anyway. [ 14.505433] systemd[1]: Mounting Temporary Directory (/tmp)... [ 14.524688] systemd[1]: Starting Journal Service... [ 14.544562] systemd[1]: Starting Create list of static device nodes for the current kernel... [ 14.572542] systemd[1]: Starting Load Kernel Module chromeos_pstore... [ 14.599432] systemd[1]: Condition check resulted in Load Kernel Module drm being skipped. [ 14.608848] systemd[1]: Starting Load Kernel Module efi_pstore... [ 14.628312] systemd[1]: Starting Load Kernel Module pstore_blk... [ 14.648431] systemd[1]: Starting Load Kernel Module pstore_zone... [ 14.672353] systemd[1]: Starting Load Kernel Module ramoops... [ 14.692335] systemd[1]: Starting NVIDIA specific first-boot udev script... [ 14.716338] systemd[1]: Started Nameserver information manager. [ 14.735561] systemd[1]: Reached target Network (Pre). [ 14.755791] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 14.765138] systemd[1]: Condition check resulted in File System Check on Root Device being skipped. [ 14.775749] systemd[1]: Starting Load Kernel Modules... [ 14.796510] systemd[1]: Starting Remount Root and Kernel File Systems... [ 14.804055] EXT4-fs (nvme0n1p1): re-mounted. Opts: (null) [ 14.824597] systemd[1]: Starting udev Coldplug all Devices... [ 14.825297] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 14.837743] nvmap_page_pool_init: Total RAM pages: 1907252 [ 14.845936] nvmap_page_pool_init: nvmap page pool size: 238406 pages (931 MB) [ 14.855667] nvmap_background_zero_thread: PP zeroing thread starting. [ 14.857273] systemd[1]: Started Journal Service. [ 15.106876] systemd-journald[248]: Received client request to flush runtime journal. [ 15.117014] systemd-journald[248]: File /var/log/journal/fde1f29aa5dc4324bbf0400f401d8b9c/system.journal corrupted or uncleanly shut down, renaming and replacing. [ 15.457935] nvidia: loading out-of-tree module taints kernel. [ 15.469747] nvidia: module verification failed: signature and/or required key missing - tainting kernel [ 15.497932] nv_platform 13800000.display: Adding to iommu group 52 [ 15.507314] spi-tegra114 3210000.spi: Adding to iommu group 1 [ 15.523823] imx219 9-0010: tegracam sensor driver:imx219_v2.0.6 [ 15.528971] platform 13800000.display:nvdisplay-niso: Adding to iommu group 53 [ 15.554822] spi-tegra114 3230000.spi: Adding to iommu group 1 [ 15.561566] NVRM: loading NVIDIA UNIX Open Kernel Module for aarch64 35.5.0 Release Build (buildbrain@mobile-u64-6519-d7000) Mon Feb 19 20:34:12 PST 2024 [ 15.567390] imx219 9-0010: imx219_board_setup: error during i2c read probe (-121) [ 15.592907] tegra-hda 3510000.hda: Adding to iommu group 54 [ 15.619217] r8168 0001:01:00.0: Adding to iommu group 6 [ 15.626683] imx219 9-0010: board setup failed [ 15.629010] r8168 Gigabit Ethernet driver 8.051.02.10m_pll-NAPI loaded [ 15.641463] cpu-throttle-alert cooling device registered. [ 15.647632] r8168 0001:01:00.0: enabling device (0000 -> 0003) [ 15.648534] imx219: probe of 9-0010 failed with error -121 [ 15.659887] tegra-adma 2930000.adma: Tegra210 ADMA driver registered 16 channels [ 15.661505] gpu-throttle-alert cooling device registered. [ 15.675503] imx219 10-0010: tegracam sensor driver:imx219_v2.0.6 [ 15.686893] cv0-throttle-alert cooling device registered. [ 15.695490] nvadsp 2993000.adsp: Adding to iommu group 55 [ 15.696691] input: NVIDIA Jetson Orin NX HDA HDMI/DP,pcm=3 as /devices/platform/3510000.hda/sound/card0/input4 [ 15.707570] nvadsp 2993000.adsp: in probe()... [ 15.712966] input: NVIDIA Jetson Orin NX HDA HDMI/DP,pcm=7 as /devices/platform/3510000.hda/sound/card0/input5 [ 15.713038] cv1-throttle-alert cooling device registered. [ 15.713322] cv2-throttle-alert cooling device registered. [ 15.713559] soc0-throttle-alert cooling device registered. [ 15.713795] soc1-throttle-alert cooling device registered. [ 15.714031] soc2-throttle-alert cooling device registered. [ 15.714297] hot-surface-alert cooling state: 0 -> 1 [ 15.715632] hot-surface-alert cooling device registered. [ 15.733902] imx219 10-0010: imx219_board_setup: error during i2c read probe (-121) [ 15.739870] atlantic 0004:01:00.0: Adding to iommu group 7 [ 15.742647] input: NVIDIA Jetson Orin NX HDA HDMI/DP,pcm=8 as /devices/platform/3510000.hda/sound/card0/input6 [ 15.742732] input: NVIDIA Jetson Orin NX HDA HDMI/DP,pcm=9 as /devices/platform/3510000.hda/sound/card0/input7 [ 15.760433] imx219 10-0010: board setup failed [ 15.768893] nvadsp 2993000.adsp: nvadsp_app_module_probe [ 15.780035] r8168 0001:01:00.0 (unnamed net_device) (uninitialized): Invalid ether addr 00:00:00:00:00:00 [ 15.787570] imx219: probe of 10-0010 failed with error -121 [ 15.788208] atlantic 0004:01:00.0: enabling device (0000 -> 0002) [ 15.809342] tegra-asoc: sound: Adding to iommu group 55 [ 15.818750] r8168 0001:01:00.0 (unnamed net_device) (uninitialized): Random ether addr 52:fd:2d:f2:de:ce [ 15.827490] tegra210-adsp aconnect@2a41000:adsp_audio: Adding to iommu group 55 [ 15.831859] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 15.836528] tegra210_adsp_audio_probe: platform probe started [ 15.847990] r8168 Copyright (C) 2022 Realtek NIC software team [ 15.847990] This program comes with ABSOLUTELY NO WARRANTY; for details, please see . [ 15.847990] This is free software, and you are welcome to redistribute it under certain conditions; see . [ 15.860658] tegra210-adsp tegra210-adsp: Default param-type to BYTE for mp3-dec1 [ 15.864962] atlantic: Detect ATL2FW 1030024 [ 15.865615] r8168 0009:01:00.0: Adding to iommu group 10 [ 15.871956] tegra210-adsp tegra210-adsp: Default param-type to BYTE for spkprot [ 15.903367] r8168 Gigabit Ethernet driver 8.051.02.10m_pll-NAPI loaded [ 15.910637] tegra210-adsp tegra210-adsp: Default param-type to BYTE for src [ 15.915162] r8168 0009:01:00.0: enabling device (0000 -> 0003) [ 15.920857] tegra210-adsp tegra210-adsp: Default param-type to BYTE for aac-dec1 [ 15.957459] tegra210-adsp tegra210-adsp: Default param-type to BYTE for aec [ 15.976404] tegra210-adsp tegra210-adsp: Default param-type to BYTE for wire [ 15.987858] r8168 0009:01:00.0 (unnamed net_device) (uninitialized): Invalid ether addr 00:00:00:00:00:00 [ 15.991832] tegra210-adsp tegra210-adsp: adma channel page address dt entry not found [ 16.005959] tegra210-adsp tegra210-adsp: using adma channel page 0 [ 16.006100] r8168 0009:01:00.0 (unnamed net_device) (uninitialized): Random ether addr c2:8f:93:c8:01:57 [ 16.013181] nvadsp 2993000.adsp: ADSP OS firmware already loaded [ 16.024023] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 16.043948] r8168 Copyright (C) 2022 Realtek NIC software team [ 16.043948] This program comes with ABSOLUTELY NO WARRANTY; for details, please see . [ 16.043948] This is free software, and you are welcome to redistribute it under certain conditions; see . [ 16.082276] r8168 0008:01:00.0: Adding to iommu group 9 [ 16.090097] cryptd: max_cpu_qlen set to 1000 [ 16.096380] r8168 Gigabit Ethernet driver 8.051.02.10m_pll-NAPI loaded [ 16.103902] r8168 0008:01:00.0: enabling device (0000 -> 0003) [ 16.138832] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 16.152830] r8168 Copyright (C) 2022 Realtek NIC software team [ 16.152830] This program comes with ABSOLUTELY NO WARRANTY; for details, please see . [ 16.152830] This is free software, and you are welcome to redistribute it under certain conditions; see . [ 16.356000] nvgpu: 17000000.ga10b nvgpu_nvhost_syncpt_init:135 [INFO] syncpt_unit_base 60000000 syncpt_unit_size 4000000 size 10000 [ 16.356000] [ 16.419819] tegra210-adsp tegra210-adsp: Loaded app wire [ 16.425328] tegra210-adsp tegra210-adsp: Loaded app apm [ 16.430704] tegra210-adsp tegra210-adsp: Loaded app adma [ 16.436176] tegra210-adsp tegra210-adsp: Loaded app adma_tx [ 16.441914] nvadsp_set_adma_dump_reg: callback for adma reg dump is sent to 00000000fa04f799 [ 17.282816] [universalEthernet.c:249:camera_init] [ universalEthernet driver loaded successfully. ], deviceMajor 504